Brother DCP-J925DW Скачать руководство пользователя страница 60

Страница: 60 / 378

2-15

Confidential

3.3

Communications Error Codes

*1 Available in German models only.

Code 1

Code 2

Cause

Refer to:

Wrong number called.

Chapter 2, Section
4.9.4

No dial tone detected before start of dialing.

Busy tone detected before dialing.

2nd dial tone not detected.

No loop current detected.

Busy tone detected after dialing or called.

No response from the remote station in sending.

Unobtainable tone detected after dialing.

No response from the calling station in receiving.

Unable to detect a flag field.

Carrier was OFF for 200 milliseconds or longer.

Abort detected ("1" in succession for 7 bits or more).

Overrun detected.

A frame for 3 seconds or more received.

CRC error in answerback.

Echo command received.

Invalid command received.

Command ignored once for document setting or for
dumping-out at turn-around transmission.

T5 time-out error.

CRP received.

EOR and NULL received.

Содержание DCP-J925DW



























































































































































































































































































































































































Результаты поиска

Содержание DCP-J925DW

Отзывы:

Похожие инструкции для DCP-J925DW

Бренды по названию

Популярные бренды

Brother DCP-J925DW, Руководство по обслуживанию

Результаты поиска

Содержание DCP-J925DW

Отзывы:

Похожие инструкции для DCP-J925DW

Бренды по названию

Популярные бренды