Brother DCP-J925DW Скачать руководство пользователя страница 55

Страница: 55 / 378

2-10

Confidential

Error
Code

Contents

Refer to

page:

Abnormal stop of purge cam during head capping. (When being driven in the
capping direction)

2-41

Abnormal stop of purge cam during head uncapping. (When being driven in the
uncapping direction)

2-41

Motor driver IC overcurrent protection activated when the purge cam was being
driven.

2-42

Head property data not entered.

2-42

Recording paper size error. (During fax/list printing) (The paper size not
suitable for recording fax was detected by the paper width sensor or registration
sensor.)

2-43

Recording paper size error. (Except during fax/list printing) (The paper width
sensor has detected that the paper width is less than the specified one.)

2-44

Recording paper jam in paper feeding. (The paper width sensor has failed to
detect the leading edge of paper.)

2-44

Recording paper jam in paper ejecting. (The registration sensor sticks to ON
even after completion of paper ejection.)

2-45

Paper width sensor has failed to detect the origin defined on the paper feed
roller.

2-45

PF encoder sensor cannot detect the rotation of the paper feed roller.

2-46

PF encoder sensor detects an abnormal stop of the paper feed roller.

2-46

Driver IC overcurrent protection activated during running of the paper feed
motor.

2-47

Paper feed motor cannot stop.

2-47

Disc tray collided against an obstacle in the rear of the machine.

2-48

Pressure roller has failed to be released.

2-48

Pressure roller has failed to be depressed.

2-49

Disc size error. Or no disc is loaded on the disc tray.

2-49

Document scanner unit opened.

2-50

During ADF scanning, a document of 90 cm or longer is detected.

2-50

During ADF scanning, the document scanning position sensor does not come
ON.

2-51

Detected abnormal level data in the CIS scanning result during fax sending (1st
time).

2-51

Detected abnormal level data in the CIS scanning result during fax sending
(retry).

2-51

Mismatch between actual CIS type and EEPROM data.

2-52

Color parameter matching error. (Used for debugging at the factory.)

2-52

CIS positioning error. (Home positioning failed)

2-53

Содержание DCP-J925DW



























































































































































































































































































































































































Результаты поиска

Содержание DCP-J925DW

Отзывы:

Похожие инструкции для DCP-J925DW

Бренды по названию

Популярные бренды

Brother DCP-J925DW, Руководство по обслуживанию

Результаты поиска

Содержание DCP-J925DW

Отзывы:

Похожие инструкции для DCP-J925DW

Бренды по названию

Популярные бренды