manualshive.com logo in svg

Brother DCP-110C, Руководство по обслуживанию

Поделиться
Скачать
Brother DCP-110C Скачать руководство пользователя страница 337

 9-24 

Confidential

 

9.2 TROUBLESHOOTING 

9.2.1 Introduction 

This section gives the service personnel some of the troubleshooting procedures to be followed if 

an error or malfunction occurs with the machine. It is impossible to anticipate all of the possible 

problems which may occur in future and determine the troubleshooting procedures, so this section 

covers some sample problems.  However, those samples will help service personnel pinpoint and 

repair other defective elements if he/she analyzes and examines them well. 

 

9.2.2 Precautions 

Be sure to observe the following to prevent the secondary troubles from happening: 
(1)  Always unplug the AC power cord from the outlet when removing the covers and PCBs, 

adjusting the mechanisms, or conducting continuity testing with a circuit tester. 

(2)  When disconnecting the connectors, do not pull the lead wires but hold the connector housings. 
(3) 

z

 Before handling the PCBs, touch a metal portion of the machine to discharge static 

electricity charged in your body. 

 

z

 When repairing the PCBs, handle them with extra care. 

After repairing the defective section, be sure to check again if the repaired section works correctly.  

Also record the troubleshooting procedure so that it would be of use for future trouble occurrence. 

 

9.2.3  Checking prior to Troubleshooting 

Prior to proceeding to the troubleshooting procedures given in 

Section 9.2.4,

 make the following 

initial checks: 

Environmental conditions 
Check that: 
(1)  The machine is placed on a flat, firm surface. 
(2)  The machine is used in a clean environment at or near normal room temperature (10

°

C to 

35

°

C) with normal relative humidity (20 to 80%). 

(3)  The machine is not exposed to direct sunlight or harmful gases. 

Power requirements 
Check that: 
(1)  The power supply specified on the rating plate on the machine is used. The supply voltage 

stays within the rating ±10%. 

(2)  Each voltage level on AC input lines and DC lines is correct. 
(3)  All cables and harnesses are firmly connected. 
(4)  None of the fuses are blown. 

Содержание DCP-110C



















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды