Brother CS-8072 Скачать руководство пользователя страница 74

Страница: 74 / 82

Mechanical trouble

Probable cause

1. Feed dog is lowered.

2. Stitch length is set at no feeding.

3. The combination of selected stitch and

presser foot is not correct.

4. Correct needle is not being used.

5. Thread is entangled.

1. Needle is not correctly inserted.

2. Correct needle is not used.

3. The combination of fabric, thread and

needle is not correct.

4. The fabric is pulled too much.

1. “START/STOP” button is not pressed.

2. Main power switch is in the off position.

3. Presser foot is not lowered.

Remedy

1. Raise the feed dog with the feed dog

position switch.

2. Set stitch length properly.

3. Change presser foot to correct one.

4. Change to proper needle.

5. Remove thread-ends in the race or

inner shuttle.

1. Set needle properly.

2. Change to proper needle.

3. Check the “FABRIC/THREAD/NEEDLE

COMBINATION CHART” on page 26.

4. Guide the fabric allowing it to sew

without pulling.

1. Press “START/STOP” button.

2. Turn the power on.

3. Lower the presser foot.

Symptom

1. Fabric is not fed properly

2. Needle breaks

3. Machine does not start

Note
–

If the power goes out while the sewing machine is being operated:
Turn off the sewing machine and unplug its power cord.
When the sewing machine is restarted, operate it correctly according to the operating procedure.

•

When operating correctly : 1 beep

•

When operating incorrectly : 2 beeps or 4 beeps

Alarm

CONTENTS

BEFORE USE

SEWING

UTILITY STITCHES

MAINTENANCE

SEWING CHAR

TTERNS

(PR

OGRAMMED IN

CHINE)

Содержание CS-8072



















































































Результаты поиска

Содержание CS-8072

Отзывы:

Похожие инструкции для CS-8072

Бренды по названию

Популярные бренды

Brother CS-8072, Руководство по эксплуатации

Результаты поиска

Содержание CS-8072

Отзывы:

Похожие инструкции для CS-8072

Бренды по названию

Популярные бренды