Brother CS-8072 Скачать руководство пользователя страница 58

Страница: 58 / 82

CONTENTS

BEFORE USE

SEWING

UTILITY STITCHES

MAINTENANCE

SEWING CHAR

TTERNS

(PR

OGRAMMED IN

CHINE)

FLAT FELL SEAM

1. Attach presser foot “J”. Sew the seam line, then cut half of the

seam allowance from the side that the flat fell seam will lie
against.

About 12 mm (1/2")

Wrong side of fabric

2. Spread out the fabric along the finish line.

Finish line

Wrong side of fabric

3. Lay both seam allowances to the shorter one’s (cut one) side

and iron them.

Wrong side of fabric

4. Fold the longer seam allowance around the shorter one, and

sew the edge of the fold.

Wrong side of fabric

Flat-fell seam can be on the inside or outside. For example for
denim jeans, jackets, etc., seam is on the outside, rather than
inside as shown above.

For reinforcing seams and neatly finishing edges

Содержание CS-8072



















































































Результаты поиска

Содержание CS-8072

Отзывы:

Похожие инструкции для CS-8072

Бренды по названию

Популярные бренды

Brother CS-8072, Руководство по эксплуатации

Результаты поиска

Содержание CS-8072

Отзывы:

Похожие инструкции для CS-8072

Бренды по названию

Популярные бренды