Brother CS-8072 Скачать руководство пользователя страница 15

Страница: 15 / 82

CONTENTS

BEFORE USE

SEWING

UTILITY STITCHES

MAINTENANCE

SEWING CHAR

TTERNS

(PR

OGRAMMED IN

CHINE)

Setting the bobbin

1. Slide open the bobbin cover.

Bobbin cover

Bobbin cover release button

2. Insert the bobbin into the shuttle with the thread direction as

shown in the diagram.

3. Guide the thread end through the slit, then pull the thread to-

ward you to cut off any excess thread.

Built-in thread cutter

4. Close the bobbin cover by placing the left end in place and

pressing down lightly on the right end so that it snaps into
place.

You can begin sewing immediately without drawing up the bob-
bin thread.

CAUTION

Setting the bobbin improperly may cause the thread tension to
loosen, breaking the needle and resulting in injury.

Wound evenly

Wound poorly

CAUTION

Be sure the bobbin is set so the thread unrolls in the
correct direction. If the thread unrolls in the wrong
direction, it may cause the thread tension to be
incorrect or the needle to break.

Содержание CS-8072



















































































Результаты поиска

Содержание CS-8072

Отзывы:

Похожие инструкции для CS-8072

Бренды по названию

Популярные бренды

Brother CS-8072, Руководство по эксплуатации

Результаты поиска

Содержание CS-8072

Отзывы:

Похожие инструкции для CS-8072

Бренды по названию

Популярные бренды