Brother BAS-761 Скачать руководство пользователя страница 35

Страница: 35 / 155

Programmer

Chapter 2 Programming with Help Function

Needle racking

Needle tacking is programmed.

Tacking width is set with the dial on the back of the top part of

the machine while needle tacking length is set with the pro-

grammer. Values 1.0 to 3.5 mm are available for the tacking

width.

Values 0.1 to 1.0 mm are available for the stitch length.

The needle actually drops at the point B' because needle tacking is conducted on the machine side. However, point

B of the program is created on the straight line between point A and point C.

Programming

Create the program to point A.

Select

with

, then press

Input the stitch length, then press

0.5 mm is input in the example.

Input 050 to make the width and the stitch length to 0.5 mm.

Move the needle with

. Press

when the needle point is at point B of the

pattern.

Press

ESC

twice.

Continue programming.

Zigzag

width

Stitch length

Содержание BAS-761




























































































































































Результаты поиска

Содержание BAS-761

Отзывы:

Похожие инструкции для BAS-761

Бренды по названию

Популярные бренды

Brother BAS-761, Инструкция по эксплуатации

Результаты поиска

Содержание BAS-761

Отзывы:

Похожие инструкции для BAS-761

Бренды по названию

Популярные бренды