Brother 882-D80, Руководство по эксплуатации

Страница: 171 / 180

TROUBLESHOOTING
Main
te
nan
ce
a
nd
Tr
oubl
es
hoo
ting
Appendix A-21
A
2
Machine does not
operate There is no pattern selected. Select a pattern. E-3, E-58
“Start/Stop” button was not pushed. Press the “Start/Stop” button. B-10
Main power switch is not turned on. Turn the main power to ON. B-17
Presser foot is not lowered. Lower the presser foot. B-10
All keys and buttons have been locked by
.
Press to unlock all keys and
buttons.
B-42, B-45
Nothing happens,
even if the LCD
display is pressed The screen has been locked. Press either of the following keys to unlock
the screen.
—
The fabric feeds in the
opposite direction. The feed mechanism is damaged. Contact your dealer or the nearest authorized
service center. —
The LCD screen is
fogged up. Condensation has formed on the LCD screen. After a while, the cloudiness will disappear. —
Embroidery pattern
does not sew out
correctly Thread is twisted. Use scissors, etc., to cut the twisted thread
and remove it from the race, etc. A-13
Fabric was not inserted into the frame correctly
(fabric was loose, etc.). If the fabric is not stretched tight in the frame,
the pattern may turn out poorly or there may
be shrinkage of the pattern. Set the fabric
into the frame correctly. E-14
Stabilizing material was not attached. Always use stabilizing material, especially
with stretch fabrics, lightweight fabrics,
fabrics with a coarse weave, or fabrics that
often cause pattern shrinkage. See your
authorized dealer for the proper stabilizer. E-11
There was an object placed near the machine,
and the carriage or embroidery frame hit the
object during sewing. If the frame bumps something during sewing,
the pattern will turn out poorly. Do not place
anything in the area where the frame may
bump it during sewing. E-21
Fabric outside the frame edges interferes with
the sewing arm, so the embroidery unit cannot
move. Reinsert the fabric in the embroidery frame so
that the excess fabric is away from the
sewing arm, and rotate the pattern 180
degrees. E-14
Fabric is too heavy, so the embroidery unit
cannot move freely. Place a large thick book or similar object
under the arm head to lightly lift the heavy
side and keep it level. —
Embroidery pattern
does not sew out
correctly Fabric is hanging off the table. If the fabric is hanging off the table during
embroidery, the embroidery unit will not
move freely. Place the fabric so that it does
not hang off the table or hold the fabric to
keep it from dragging. E-21
Fabric is snagged or caught on something. Stop the machine and place the fabric so that
it does not get caught or snagged. —
Embroidery frame was removed during sewing
(for example, to reset the bobbin). The
embroidery foot was bumped or moved while
removing or attaching the embroidery frame, or
the embroidery unit was moved. If the embroidery foot is bumped or the
embroidery unit is moved during sewing, the
pattern will not turn out. Be careful when
removing or reattaching the embroidery
frame during sewing. E-26
Stabilizer is incorrectly attached, for example, it
is smaller than the embroidery frame. Attach the stabilizer correctly. E-11
Loops appear on the
surface of the fabric
when embroidering The thread tension is incorrectly set. Adjust the thread tension. E-30 to E-32
The tension of the upper thread is incorrectly
set for the combination of the fabric, thread and
pattern being used. Use the embroidery needle plate cover. E-22
The combination of the bobbin case and
bobbin thread is incorrect. Change the bobbin case or bobbin thread so
that the correct combination is used. E-21
Embroidery unit does
not operate There is no pattern selected. Select a pattern. E-3, E-58
Main power switch is not turned on. Turn the main power to ON. B-17
Embroidery unit is not attached correctly. Reattach the embroidery unit correctly. B-47
Embroidery frame was attached before the unit
was initialized. Perform the initialization process correctly. B-47
Pointer of embroidery
foot “W+” with LED
pointer does not
indicate the position
correctly With thick or elastic fabric, the position will be
misaligned only at raised parts in the fabric. Manually adjust the position according to the
thickness of the fabric. B-44
With fabric having a very uneven surface, the
position is not correctly aligned. The pointer indication should be used only as
a reference. B-43
Problem Cause Solution Page