Brooks Instrument GP200 Series Скачать руководство пользователя

Страница: 38 / 45

Series. Observe for consistency.

4. Verify isolations valves are open and the gas supply is turned on.

Then verify operating pressures are within operating ranges.

5. Check GP200 Series voltage response by moving the setpoint

back and forth. Observe for voltage changes.

Table 4-1 Environmental Factors

GP200 Series Performance

Possible Causes

Inaccurate flow.

Temperature shift (steady state or transient).

Inlet pressure shift (steady state or transient).

Power supply problem.

Electrical interference

Dirty gas chamber

Changes in gas.

Control problems.

Cannot reach setpoint.

Oscillation.

Differential pressure not within operating range

Inlet pressure not stable

Zeroing problems, Indicated

zero is not stable.

Temperature shift (steady state or transient).

Inlet pressure shift (steady state or transient).

Power supply problem.

Electrical interference

GP200 Series Troubleshooting Guide

Table 4-2 GP200 Series Troubleshooting Guide

Symptoms & Possible Causes

Corrective Action

1. No gas flow.

Is the gas supply turned on?

Check shut-off valve and pressure readout. Open

the gas supply.

Is the regulator turned on at the

correct operating pressure?

Turn off the regulator and reset it to the

recommended pressure as described in the

Data Sheet.

Are any upstream or downstream

shut-off valves closed, either by

the system or because of failure?

Verify that the valves are open and operating

properly.

Is the MOD LED light on the GP200 Series

lit solid green? (DeviceNet Models only)

Observe the LED display panel on top of to

verify. If the LED light is not lit, cycle power the

to reboot.

Is the commanded setpoint from

tool/system at 0.00 Vdc?

Use the tool software to verify.

Has the MFC been commanded

off by an active “valve

closed” input?

Use the tool software to verify.

2. Flow out of range.

Section 4 Maintenance & Troubleshooting

Содержание GP200 Series














































Результаты поиска

Содержание GP200 Series

Отзывы:

Похожие инструкции для GP200 Series

Бренды по названию

Популярные бренды

Brooks Instrument GP200 Series, Руководство по установке и эксплуатации

Результаты поиска

Содержание GP200 Series

Отзывы:

Похожие инструкции для GP200 Series

Бренды по названию

Популярные бренды