BRONKHORST FLOW-SMS Series Скачать руководство пользователя страница 14

Страница: 14 / 26

Bronkhorst

9.17.057

page 14

2.13.7 Needle Valves

Removal

Ensure that the system is depressurised before taking the

needle valve apart.

Loosen the 4 bolts with hexagon head counter clockwise

to release the needle valve.

Replacement

Replace the gaskets AS-007 and AS-017,Viton,

EPDM or Kalrez.

All wetted parts have to be absolutely clean, don’t use oil

or grease and avoid dust!

Replace the needle valve centre before tighten the bolt

with hexagon head by turning clockwise, tighten crosswise

with M3 0,9 Nm.

Now the needle valve has to be tested for leakage and function.

Adjustment

The needle valves are adjustable

with a slotted headscrewdriver to adjust the flow.

The NV-01 is also lockable with a

nut because the fine adjustability.

2.13.8 Pneumatic operated shut off valves NC or NO

The actuating pressure has to be supplied with a 3/2 way valve.

When the valve is not actuated the air actuation input has to vent.

Actuation pressure

Minimal

: 3 bar(g).

Maximal

: 9

bar(g).

Removing

Ensure that the system is depressurised before taking

the pneumatic shut off valve apart.

Remove the actuating pressure tubing and loosen the 4 bolts

with hexagon head counter clockwise to release the valve.

Replacing

Replace the gasket AS-007 and AS-017, Viton, EPDM or Kalrez.

All wetted parts have to be absolutely clean, don’t use

oil or grease and avoid dust!

Replace the pneumatic shut off valve and tighten the

bolts with hexagon head by turning clockwise, tighten

crosswise with M3 0,9 Nm.

Replace the actuating pressure tubing.

Now the pneumatic shut off valve has to be tested for leakage and function.

Available Needle valves

Model number

Description

NV-01

Kvmin 1.0x10

-3

,Kvmax 6.8x10

-3

Low flow needle valve, fine

NV-02

Kvmin 5.6x10

-3

,Kvmax 5.6x10

-2

High flow needle valve, coarse

Available Pneumatic shut off valves

Model number

Description

PV-01-NC-V

Kv=0,20

Normally Closed Viton

PV-01-NC-E

Kv=0,20

Normally Closed EPDM

PV-01-NC-K

Kv=0,20

Normally Closed Kalrez

PV-01-NO-V

Kv=0,20

Normally Open Viton

PV-01-NO-E

Kv=0,20

Normally Open EPDM

PV-01-NO-K

Kv=0,20

Normally Open Kalrez

Содержание FLOW-SMS Series



























Результаты поиска

Содержание FLOW-SMS Series

Отзывы:

Похожие инструкции для FLOW-SMS Series

Бренды по названию

Популярные бренды

BRONKHORST FLOW-SMS Series, Инструкция по эксплуатации

Результаты поиска

Содержание FLOW-SMS Series

Отзывы:

Похожие инструкции для FLOW-SMS Series

Бренды по названию

Популярные бренды