BRONKHORST FLOW-SMS Series Скачать руководство пользователя

Страница: 8 / 26

Bronkhorst

9.17.057

page 8

When connecting the system to other devices (e.g. to PLC), be sure that the integrity of the

shielding

not affected. Do not use unshielded wire terminals.

Operation via fieldbus is done by means of a

flat conductor

cable

connected with the main PC board.

Although all functionality is possible by means of RS232

and the switch on top of the instrument, it is important

that care should be taken when removing the upper part

of the housing.

In case that a shut-off valve is mounted directly behind a control

module, please apply a

right angled connector

for Analog/RS232

communication.

2.7 Analog / Digital operation

2.7a Analog/Local operation

Connect the Mass Flow or Pressure Meter/Controller

to the power supply/readout unit using a cable with

9-pin sub-D connector.

2.7b Digital/Fieldbus operation

For this procedure see description for RS232 or the applicable

fieldbus operation.

RS232 connection cable 7.03.366 enables to use (free)

Bronkhorst® tooling programs for Windows

2.8 Multi-functional switch operation

Using the 2 colored LEDs and the switch on the instruments,

several actions can be monitored and started. The green LED

is used for status indication. The red LED is used for errors/

warnings/messages. The switch can be used to start several

actions, such as auto-zero, restore factory settings and bus-

initialization actions, if applicable.

See specific zero-procedure below (10) for more details.

Error/warning LED

Status LED

Multifunctional

switch

EXAMPLE

Power:

+15...+24 Vdc

Analog input / output:

0…5Vdc / 0…10Vdc

0…20mA / 4…20mA

7.03.366

Содержание FLOW-SMS Series



























Результаты поиска

Содержание FLOW-SMS Series

Отзывы:

Похожие инструкции для FLOW-SMS Series

Бренды по названию

Популярные бренды

BRONKHORST FLOW-SMS Series, Инструкция по эксплуатации

Результаты поиска

Содержание FLOW-SMS Series

Отзывы:

Похожие инструкции для FLOW-SMS Series

Бренды по названию

Популярные бренды