background image

20 

11.2 

Charging battery 

 
The mains cable for charging the Power Dock is stored in the cover (34). Connect the 
mains cable to the connection socket (34) of the Power Dock as well as to the mains 
supply. The charging mode of the battery has two levels, which are displayed by the 
flashing charge display (33).   
 
Level 1:  The battery is charged in fast charge mode up to approx. 80 % of full charge. 

Duration, depending on state of charge, up to 3 hours.  

 
Level 2:  The  battery  is  being  recharged  slowly  to  100  %  (duration  up  to  approx.  5 

hours) and then kept on charge.  

 
Attention: Do not operate the Verso A with the Power Dock during charging. 

 

11.3 

Care of the Power Dock 

 
The battery used is sealed and does not require any special care. It does not show any 
particular  "memory  effect"  and  does  not  need  to  be  discharged  regularly.  Ensure, 
however,  that  the  battery  package  never  runs  down.  The  bottom  bar  (10  %  of  battery 
capacity)  should  always  be  visible.  Therefore,  Verso  A  and  Power  Dock  switch  off 
automatically when the battery voltage sinks too low.  As a leakage current  flows even 
when  the  unit  is  switched  off,  it  is  highly  recommendable,  to  fully  charge  the  Power 
Dock after use. Additionally, the charge situation must be controlled every two months 
and the battery package has to be fully recharged.   
 
If the charge display does not show a fully charged battery package and the value does 
not change within the next 1 

– 2 hours even though connected to the mains cable, the 

battery must be controlled by a local broncolor service station.     

 
 
 

12.  Lamp bases 

 

In  the  "fast  charging  mode"  the  power  pack  Verso  A2  and  Verso  A4  has  a  very  high 
charging capacity. Therefore each connected lamp base has to be equipped with a flash 
tube  with  high  power  rating.  Thus  in  this  mode  the  Verso  A2  and  Verso  A4  must  be 
operated at present only with the following lamp bases: 

 

12.1 

Verso A2 

 

Mains and battery operation 

 

- Lamp base Pulso G with flash tube 1600 J 

1)

 

- Lamp base Pulso G with flash tube 3200 J 

1)

 

- Lamp base Unilite with flash tube 1600 J 

1)

 

- Lamp base Unilite with flash tube 3200 J 

1)

 

- Special effect lamp Litestick

 

- Ringflash C

 

- Ringflash P

 

 

Содержание Verso A2 plus




























Отзывы: