manualshive.com logo in svg

Brocade Communications Systems Brocade 8/12c, Справочник по командам

Продукт Brocade Communications Systems Brocade 8/12c - это высококачественный коммутатор для сетевых систем. Для установки устройства вам потребуется Руководство по установке, которое можно бесплатно скачать на manualshive.com. Получите доступ к инструкции прямо сейчас и наслаждайтесь отличным качеством обслуживания вашей сети.

Поделиться
Скачать
background image

412

Fabric OS Command Reference

53-1001764-01

haShow

22

haShow

Displays control processor (CP) status. 

SYNOPSIS

hashow

DESCRIPTION

Use this command to display the control processor status. The display includes the following information:

•

Local CP state (slot number and CP ID), warm or cold, recovering or recovered.

•

Remote CP state (slot number and CP ID).

•

High Availability (enabled or disabled).

•

Heartbeat (up or down).

•

Health of standby CP

•

HA synchronization status

The health of the standby CP is defined as follows:

Healthy

The standby CP is running and the background health diagnostic has not detected 
any errors.

Failed

The standby CP is running, but the background health diagnostic has discovered 
a problem with the blade. Check the logs to determine the appropriate action. 
Failover is disabled until the standby CP is repaired. Information about the failing 
device in the standby CP is displayed.

Unknown

The standby CP health state is unknown because of one of the following reasons: 
the standby CP does not exist, Heartbeat is down, or the Health Monitor has 
detected a configuration file error.

The High Availability synchronization status is defined as follows:

HA State synchronized 

The system is currently fully synchronized. If a failover becomes necessary, it is 
nondisruptive.

HA State not in sync 

The system is unable to synchronize the two CPs. This may be caused by one or 
more of the following conditions:

•

The 

haFailover

 command was issued. In this case the "HA State not in sync" 

state is transitory.

•

The standby CP is faulty.

•

 The 

haSyncStop

 command was issued.

•

A system error occurred.

If a failover becomes necessary while the CPs are not in sync, the standby CP 
reboots, and the failover is disruptive.

NOTES

This command may not be supported on nonbladed systems.

Slot numbers for CP1 and CP0 vary depending on the hardware platform. On the Brocade DCX and DCX 
8510-8, CP0 is in slot 6 and CP1 is in slot 7. On the Brocade DCX-4S, and DCX 8510-4, CP0 is in slot 4 
and CP1 is in slot 5.

The execution of this command is subject to Virtual Fabric or Admin Domain restrictions that may be in 
place. Refer to Chapter 1, "Using Fabric OS Commands" and Appendix A, "Command Availability" for 
details.

Содержание Brocade 8/12c













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Brocade 8/12c

M-Audio Afro-Cuban Percussion Quick Start Manual preview
Afro-Cuban Percussion
Бренд: M-Audio Страницы: 5
Barco NioWatch Installation & User Manual preview
NioWatch
Бренд: Barco Страницы: 22
Nortel CC MIS User Manual preview
CC MIS
Бренд: Nortel Страницы: 374
Teklynx Discover ActiveX Programmer'S Manual preview
Discover ActiveX
Бренд: Teklynx Страницы: 165
FARONICS DEVICE FILTER MAC Manual preview
DEVICE FILTER MAC
Бренд: FARONICS Страницы: 30
Kenwood MediaManager Installation Manual preview
MediaManager
Бренд: Kenwood Страницы: 40
Sharp PixLab Online Manual preview
PixLab
Бренд: Sharp Страницы: 12
2Wire Third-Party Installation Manual preview
Third-Party
Бренд: 2Wire Страницы: 35
Vonamic 703100 Configuration Manual preview
703100
Бренд: Vonamic Страницы: 31
UNIBLUE DiskRescue 2009 Manual preview
DiskRescue 2009
Бренд: UNIBLUE Страницы: 26
GRASS VALLEY EDIUS SP Datasheet preview
EDIUS SP
Бренд: GRASS VALLEY Страницы: 4
MACROMEDIA COLFUSION MX 7-GETTING STARTED BUILDING COLDFUSION... Getting Started preview
COLFUSION MX 7-GETTING STARTED BUILDING COLDFUSION...
Бренд: MACROMEDIA Страницы: 152
IBM High Performance Storage System HPSS Installation Manual preview
High Performance Storage System HPSS
Бренд: IBM Страницы: 311
MACROMEDIA FLASH MX 2004-ACTIONSCRIPT LANGUAGE Reference preview
FLASH MX 2004-ACTIONSCRIPT LANGUAGE
Бренд: MACROMEDIA Страницы: 1104
FARONICS DEEP FREEZE ENTERPRISE - TREND MICRO OFFICESCAN... Manual preview
DEEP FREEZE ENTERPRISE - TREND MICRO OFFICESCAN...
Бренд: FARONICS Страницы: 17
Zeta PC3K User Manual preview
PC3K
Бренд: Zeta Страницы: 46
IVT BlueSoleil User Manual preview
BlueSoleil
Бренд: IVT Страницы: 49
Patton electronics IPLink Series Software Configuration Manual preview
IPLink Series
Бренд: Patton electronics Страницы: 331

Бренды по названию

Популярные бренды

Загрузить еще бренды