background image

®

Page 2

MODELS 678 • 678MX • 679 • 680 • 679FL • 680FL

3. Set housing aside and drive nails partially into joist at the

top of both keyhole marks.

4. Hang housing from nails and pound nails tight. To ensure

a noise-free mount, pound another nail through the top
hole of each mounting tab.

INSTALL THE HOUSING
(continued)

New Construction

Existing Construction

2. In attic, position mounting brackets against joist. Trace

outline of housing on ceiling material.

1. Choose the location for your fan/light in the ceiling. For

best possible performance, use the shortest possible duct
run and a minimum number of elbows.

3. Set housing aside and cut ceiling opening slightly larger

than marked.

TYPICAL INSTALLATIONS
(continued)

INSTALL THE HOUSING

1. Choose the location for your fan in the ceiling. For best

possible performance, use the shortest possible duct run
and a minimum number of elbows.

2. Position mounting brackets against joist so that bottom

edge of housing will be flush with finished ceiling.

Additional positioning feature for 5/8”, 1”, &
1-1/4” thick ceiling material:
Holes in corners of housing are labeled with various
ceiling material thicknesses. Position housing so
bottom edge of joist is visible through a matched
set of holes. The housing is now in the proper
position for that ceiling material thickness.
Additional positioning feature for 1/2” thick
ceiling material:
Bend two tabs, on side of housing, 90

0

 outward. Lift

housing until tabs contact underside of joist.

Mark the keyhole slot on both mounting brackets.

New Construction

5/8

1

1-1/4

TAB

HOLES

BOTTOM EDGE OF JOIST

MOUNTING

TAB

GRILLE

SUSPENDED

CEILING MATERIAL

POWER

CABLE

4" ROUND

DUCT

HOUSING

SUSPENDED CEILINGS

Housing hung with wires - 3-point mount.

- PLEASE NOTE -

THE FOLLOWING INSTALLATION ILLUSTRATIONS SHOW 2 X 6
JOISTS. IF YOU HAVE A TRUSS OR “I”-JOIST INSTALLATION,
MOUNT THE VENTILATOR TO THE ADDITIONAL FRAMING IN THE
SAME MANNER. (Additional framing must be a 2x6 (minimum height),
at least 9-inches long.)

Broan at

::

bathroomsource

.

com

is a division of

kitchen

::

accessories

U      N      L      I      M      I      T      E      D

::

bathroomsource

.

com

                   

Call 1-800-667-8721 anywhere in the US and Canada -

www.bathroomsource.com

Содержание 678









Отзывы: