background image

e-mail: 

[email protected]   

voice: 

360.854.9559   

fax: 

866.783.1742

27

WVRC-8 Installation and Operation Manual

SETUP

4 - Start the “Device Installer” software. 

a

- Click on 

“SEARCH”

b

- When the WVRC-8 is found, click on the listed device.  If more than one WVRC-8 is

found, refer to the MAC address label attached to the WVRC-8 RJ-45 case and click
on the desired WVRC-8, which should be highlighted.

NOTE: 

Locate the MAC address label attached to the top of chassis.

c

- Click on the 

“ASSIGN IP”

button, then follow the instructions for setting a static IP

address, along with the subnet and gateway, if applicable.  

d

- After rebooting the WVRC-8, set you computer IP setting back to it’s original settings

and access the WVRC-8 at it’s new address or click the 

“SEARCH”

button, the con-

figured WVRC-8 should be listed.  

NOTE:

You may have to click the search button more than once after the reboot. 

NOTE:

You can also open your browser and type in the assigned IP address in the

“ADDRESS” area of your browser. 

Example:

192.168.1.101

5 - If you are behind a firewall or router, you will need to port forward not only port 80,

but also open ports 3001, 3002, 10001 and set the SUN Java to direct.  

NOTE:  

To set up port forwarding, refer to the manual supplied with the firewall or

router.

6 - To change the WVRC-8 from 

port 80, contact the factory

7 - To access the WVRC-8, open your browser and type in the assigned IP address in the

“ADDRESS” area of your browser.  

Example:

192.168.1.101

NOTE:  We recommend using the latest version of the FireFox or Safari web browser.

8 - If things are working correctly, you should see the WVRC-8 web page. 

NOTE:

On some machines and browsers, this may take a few seconds.

9 - Log in using the 

default: user name either 

wvrc8 or admin (lower case)

and password:  either 

wvrc8 (lower case) or 1234

NOTE:  

If you change the user name and password, 

be sure to write it down.

10 – Follow the descriptions on the following pages to set up the WVRC-8. 

The WVRC-8 software consists of two components – firmware running in the
Xport and a Java applet hosted on the Xport, running in a web browser.  This
document describes the operation of both components.

WEBSITE:

Visit our web site for
product updates and
additional information.

Содержание WVRC-8











































Отзывы: