background image

ENGLISH 

 

OPERATION MANUAL 

 

 
BRITEQ

®

 

6/12 

BT-SUNRAY 130R 

FAN 

Used to set the working mode of the cooling system. 

  Use the 

▼/▲ buttons to browse the MENU until the required function shows up. 

  Select the function with the ENTER-button.  

  Use 

▼/▲ buttons to select the desired mode: 

 

SILENT 

The fans are temperature controlled, low fan speed for use in a quiet location.

 

Note that the light output is reduced when the LED temperature becomes too high. 

 

AUTO 

The fans are temperature controlled, high fan speed for increased cooling.

 

  Once the correct option shows on the display, press the ENTER-button to save it. 

Remark: this option can be overruled using the DMX-control channel. 

 

TEMP 

Used to show the temperature of the LEDs. 

  Use the 

▼/▲ buttons to browse the MENU until the required function shows up. 

  Select the function with the ENTER-button.  

  Use 

▼/▲ buttons to select the desired mode: °C / F 

 

DEFAULT SETTINGS 

Used to quickly select the basic settings for BLINDER or EXPO functions 

  Use the 

▼/▲ buttons to browse the MENU until the required function shows up. 

  Select the function with the ENTER-button.  

  Use 

▼/▲ buttons to select the desired mode: 

 

BLINDER: 

most obvious settings for use as a BLINDER

 

 

EXPO: 

most obvious settings for use as an EXPO projector

 

  Once the correct option shows on the display, press the ENTER-button to save it. 

PARAMETER name 

BLINDER mode  defaults 

EXPO mode defaults 

CHANNEL mode 

BLIND 8b 

EXPO WW 

NO DMX mode 

BLACKOUT 

ST.ALONE 

DIM Curve 

Square 

Square 

Dimmer Speed 

100 (440ms) 

100 (440ms) 

FAN Set 

Auto 

Silent 

Backlight 

1 min. 

1 min. 

AUTO LOCK MENU 

OFF 

OFF 

no DMX blink display 

ON 

OFF 

Temp C/F 

Celcius 

Celcius 

 

FIRMWARE VERSION 

Used to show the current version of the firmware. 

  Use the 

▼/▲ buttons to browse the MENU until the required function shows up. 

  Select the function with the ENTER-button: the current firmware version is shown. 

 

Note:  The  firmware  of  this  unit  can  be  upgraded  using  our  specia

l  “Firmware  Updater  2”  (separately 

available from Briteq

®

). More information about this can be found in the user manual of the firmware updater 

or our websitehttps://briteq-lighting.com/firmware-updater-2  

 

OVERHEAD RIGGING 

 

Important:

 

The  installation  must  be  carried  out  by  qualified  service  personal  only.  Improper 

installation  can  result  in  serious  injuries  and/or  damage  to  property.    Overhead  rigging  requires 
extensive  experience!  Working  load  limits  should  be  respected,  certified  installation  materials 
should be used, the installed device should be inspected regularly for safety.

 

  Make sure the area below  the installation place  is free from unwanted persons  during rigging, de-rigging 

and servicing. 

  Locate  the  fixture  in  a  well  ventilated  spot,  far  away  from  any  flammable  materials 

and/or liquids. The fixture must be fixed 

at least 50cm

 from surrounding walls. 

  The device should be installed out of reach of people and outside areas where persons 

may walk by or be seated.  

  Before  rigging  make  sure  that  the  installation  area  can  hold  a  minimum  point  load  of 

10times the device’s weight. 

Содержание BT-SUNRAY 130R

















Отзывы: