background image

ENGLISH 

 

OPERATION MANUAL 

 

 
BRITEQ

®

 

9/12 

BT-SUNRAY 130R 

OPERATING INSTRUCTIONS 

Note: 

when the projector is switched on the display shows “UPDATE WAIT …” This message informs you 

that IF you want to upgrade the firmware, you should do it while this message is shown on the display. For 
normal use you can ignore this message completely. 

 
STANDALONE OPERATION 

  Connect the projector(s) to the mains. 

  Make sure that the option NO DMX BEHAVIOR in the setup MENU is set to: ST.ALONE 

  In the setup MENU select the option ST.ALONE and set the desired dimmer level. 

  If used in a quiet environment: select the option FAN and chose SILENT mode.  

 

DMX OPERATION 

  Connect all units together. Refer to the 

chapter “Electrical installation for two or more units in DMX-mode” 

to learn how to do this (don’t forget to address all units properly!)  

  Connect all units to the mains and turn on the DMX controller. 

  Since  each  unit  has  its  own  DMX-address,  you  can  control  them  individually.  Remember  that  each  unit 

can use a different number DMX-channels, depending on the DMX-mode you have selected in the MENU.  

 

BLIND  BLIND  EXPO  EXPO 

DMX 

FUNCTION 

REMARKS 

8b 

16b 

WW  DTW  VALUES 

000-255 

DIM WHITE coarse 

See control channel for RED SHIFT 

  

  

  

000-255 

DIM WHITE fine 

  

  

  

000-255 

DIM AMBER coarse 

RED SHIFT ACTIVE: not used 

  

  

  

000-255 

DIM AMBER fine 

RED SHIFT ACTIVE: not used 

  

  

  

STROBE CHANNEL 

  

000-007 

   Open (no strobe) 

  

008-126 

   Random 

strobe (slow→fast)

 

  

127-131 

   Open (no strobe) 

  

132-250 

   

Normal strobe (slow→fast)

 

  

251-255 

   Closed (no output) 

  

  

  

  

CONTROL CHANNEL 

  

000-005 

   RED SHIFT 

(amber drift) ACTIVE 

NO

 3s delay used !

 

006-010 

   RED SHIFT 

(amber drift) OFF 

NO 

3s delay used !

 

011-026 

No function 

  

027-127 

   DIMMER SPEED:

 

(0,0s → 1,5s)

 

selected after 3 sec  

128-151 

No function 

  

152-157 

   FAN SILENT:

 temp. controlled, low speed 

selected after 3 sec  

158-161 

   FAN AUTO:

 temp. controlled, high speed 

selected after 3 sec 

162-167 

No function 

  

168-173 

   LINEAR

 dimmer curve 

selected after 3 sec  

174-179 

   SQUARE

 dimmer curve 

selected after 3 sec  

180-185 

   INVERSE SQUARE

 dimmer curve 

selected after 3 sec  

186-191 

   S-CURVE

 dimmer curve 

selected after 3 sec  

192-255 

No function 

  

 

Содержание BT-SUNRAY 130R

















Отзывы: