background image

ENGLISH 

 

OPERATION MANUAL 

 

 
BRITEQ

®

 

10/12 

BT-SUNRAY 130R 

RDM FUNCTIONS / REMOTE SETUP 

RDM

 

means  “

R

emote 

D

evice 

M

anagement

”.  This  projector  works  with  a  brief  set  of  RDM-functions  which 

means  that  it  can  setup  a  bi-directional  communication  with  an  RDM-compatible  DMX-controller.  Some  of 
these functions are briefly explained below, others will be added in the future. 

  The  DMX-controller  sends  out 

a  “discovery  command”,  all  RDM  devices  respond  and  send  their  unique 

device ID.

 

  The DMX-controller asks each RDM device for some basic data so it knows which devices are connected. 

The projector will respond: 

 

Device name:

    

BT-SUNRAY 130R 

 

Manufacturer:

    

Briteq

®

 

 

Category:

  

 

fixture fixed 

 

Firmware:

 x.x.x.x 

(firmware version of the projector) 

 

DMX address:

 xxx 

(current DMX start address of the projector) 

 

DMX footprint:

 xx 

(number of DMX-channels used by the projector) 

 

Personality:

 xx   

(current personality or DMX-working mode used by the projectors) 

  The  DMX-controller  can  send  certain  commands  to  each  RDM  device  which  allow  remote  setup  of  the 

units. Thanks to this the projector can be setup remotely.  

 
The following functions can be managed remotely: 

No more need to take a ladder and set all units one by one! 

 

DMX START ADDRESS:

 The start address can be set remotely from 001 to xxx.

 

 

PERSONALITY:

 The DMX working mode (DMX-chart) can be set remotely.

 

These  2  functions  make  it  possible  to  prepare  a  complete  DMX-patch  of  all  projectors  on  the  DMX-
controller and send these data to all projectors at once. More functions will be added later. 
 
 

MAINTENANCE 

  Make sure the area below the installation place is free from unwanted persons during servicing. 

  Switch off the unit, unplug the mains cable and wait until the unit has been cooled down. 

During inspection the following points should be checked: 

  All  screws  used  for  installing  the  device  and  any  of  its  parts  should  be  tightly  fastened  and  may  not  be 

corroded. 

  Housings,  fixations  and  installations  spots  (ceiling,  truss,  suspensions)  should  be  totally  free  from  any 

deformation. 

  When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced. 

  The  mains  cables  must  be  in  impeccable  condition  and  should  be  replaced  immediately  when  even  a 

small problem is detected. 

  In order  to  protect  the  device  from  overheat the  cooling  fans  (if  any)  and  ventilation  openings  should  be 

cleaned monthly. 

  The interior of the device should be cleaned annually using a vacuum cleaner or air-jet. 

  The  cleaning  of  internal  and  external  optical  lenses  and/or  mirrors  must  be  carried  out  periodically  to 

optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, 
smoky or particularly dirty surroundings can cause greater accumulation of dirt on the 

unit’s optics. 

  Clean with a soft cloth using normal glass cleaning products. 

  Always dry the parts carefully. 

Attention: We strongly recommend internal cleaning to be carried out by qualified personnel! 
 

Содержание BT-SUNRAY 130R

















Отзывы: