Brigade Sidescan SSP-6000W Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 29

Brigade Sidescan SSP-6000W Скачать руководство пользователя страница 9

3.1 Important Notes

3.2 Example Installations

This example installation shows the Sidescan

®

Predict sensor confi guration on a tipper

vehicle.

16

17

B7 CONNECTION

PLEASE ENSURE THE SPEED PULSE INPUT WIRE IS CONNECTED

TO THE B7 OUTPUT OF THE TACHOGRAPH (NOT B8)

PRE-INSTALLATION SURVEY

A PRE-INSTALLATION SURVEY IS STRONGLY RECOMMENDED TO ENSURE THE

VEHICLE IS SUITABLE FOR FITMENT OF THE SIDESCAN

®

PREDICT SYSTEM AND

TO DETERMINE THE MOST APPROPRIATE SENSOR MOUNTING LOCATIONS

SENSOR MOUNTING

PLEASE DO NOT DRILL ANY HOLES TO MOUNT THE SENSORS UNTIL THE

POSITIONS HAVE BEEN VERIFIED BY THE CONFIGURATION SOFTWARE

This installation has the dimensions given in the table below.

Where it is not possible to install sensors at the same height performance degradation can

be mitigated by positioning sensors 1, 2 and 4 lower in the array. This confi guration may be

used for installations where sensors 3, 5 and/or 6 must be mounted in or on a high wheel arch.

Ideal installation. All sensors at the same heights.

Acceptable installation. Height variation between sensors

but sensors 1, 2 and 4 are low in the array.

Vehicle length (m)

9.0

Vehicle width (m)

2.36

Installation side

Left

Number of sensors

6

Sensor horizontal distance from front of

vehicle (m)

0.36, 1.95, 3.42, 5.11, 6.55, 7.93

Sensor height above ground (m)

0.96, 1.13, 1.17, 0.99,1.19, 1.2

3

Before Installing

SSP-00HSS-B (black sensor) horizontal detection pattern (cm).

This is provided as an example only and the best sensor locations will vary from vehicle

to vehicle. Sensor confi guration will aff ect the performance of the system. Please read the

following important guidance regarding best sensor locations.

3.3 Sensor Positioning for Best System Performance

It is crucial to minimise the variation in sensor heights. This is the diff erence in height

between the highest sensor and the lowest sensor. The less variation in sensor height, the

fewer false alarms will be generated by the system. The maximum variation is 0.4 m, but

the ideal installation has all sensors at the same heights.

«
...
7
8
9
10
11
...
»

Содержание Sidescan SSP-6000W






























Отзывы:

Нет отзывов