Brigade Sidescan SSP-6000W Скачать руководство пользователя страница 7

Страница: 7 / 29

This section covers the components of the Sidescan

Predict system.

2.1 Main System Components

2.2 Full List of Contents (In 6 Sensor Kit)

SSP-1000-AI-ECU

Sidescan

Predict Algorithm ECU

SSP-1000-DPW

Sidescan

Predict Buzzer Display

SSP-1000-ECU

Sidescan

Predict UDS ECU

SSP-HSSW-KT (x 4)

Sidescan

Predict Sensor Kit (White)

SSP-10-SC

Sidescan

Predict Extension Cable - 10m

UDS-2.5BC (x 8)

3-Pin UDS Extension Cable 2.5m

SSP-0.3-AC1

Sidescan

Predict Adapter Cable -

3 to 4 pins - 30cm

SSP-0.3-AC2

Sidescan

Predict Adapter Cable -

UDS ECU to ALGO ECU - 30cm

SSP-HSSB-KT (x 2)

Sidescan

Predict Sensor Kit (Black)

SSP-0.4-SP (x 2)

Sidescan

Predict Splitter Cable - 40cm

Part

Image

Mounting location

Sidescan

Predict

Buzzer Display

• IP30.

• Mounted inside the

vehicle cab only.

• Must be clearly visible for

the driver, but not interfere

with the driver’s view.

• Mounted in a location that

reflects that the system is for

side detection only.

Sidescan

Predict

Algorithm ECU

• IP30.

• Must be mounted onto a flat

surface inside the vehicle

cab only.

• Must be mounted in correct

orientation.

• Ensure there is access to the

USB connector.

Sidescan

Predict

UDS ECU

• IP69K.

• Can be mounted in the

vehicle cab or on the body.

Sidescan

Predict

Ultrasonic Sensor

• IP69K.

• Mounted on the side of the

vehicle to monitor the blind

spot.

• Use configuration software

and pre-installation survey to

find suitable locations

Contents

Содержание Sidescan SSP-6000W






























Результаты поиска

Содержание Sidescan SSP-6000W

Отзывы:

Brigade Sidescan SSP-6000W, Руководство по установке и эксплуатации, Страница: 7 / 29

Результаты поиска

Содержание Sidescan SSP-6000W

Отзывы: