BRIG HD410 Скачать руководство пользователя страница 14

– 1 4 –

10. POTENTIAL TROUBLES AND TROUBLE-SHOOTING METHODS.

        Type of trouble

                        Probable cause

  Trouble-shooting method

1. Boat's body is not air-tight

Puncture, cut, stripping of fabric

Apply strengthening means.

Unsticking of tapes, lamination of seals

Stick tapes, bond seals.

Leakages through fill valves

Check tightness of connection

between valves and flanges.

Change packing rings.

Change valve.

2. Penetration of water inside Boat

Damage to bottom fabric

Apply strengthening means

3. Flaking off of paintwork from

Coat damaged parts with three

wooden parts

layers of polyurethan or similar

to it, sea water resistant, paint.

4. Separation of veneer from transom,

Apply epoxy resin to secure places

keel, boarding and thwarts

of separation.

Perform repair of fabric parts of the Boat according to the following procedure: clean the damaged place of the Boat to remove dirt,

use the cloth from the repair kit to cut out a patch of a required size to overlap the damaged place by at least 20 mm, round off the corners

of the patch. Treat the surfaces to be bonded using clean cloth soaced in acetone or ethylacetate. Apply two layers of adhesive to the

damaged section and strengthening means (patch) with the 5-minute interval being made. On spreading adhesive for the second time

wait for 3 minutes and then touch the stiffened adhesive with your finger to make sure that it does not stick. Apply the patch to the

damaged place without folds and wrinkles and roll it over using an object of cylindrical form.

After repair hold the Boat for at least 24 hours, then fill it up with air and test for leakproofness.

Perform repair at temperature not below - 18  C. If necessary, warm up the zones to be bonded with dry hot compressed air (50 C).

In case of veneer separation, use epoxy resin for repair. First clean the surfaces to be bonded, bond the veneer to the surface and

press it against the surface with the help of a cramp to ensure as tight connection as possible for the period of time specified in the

instructions on the use of this type of resin.

Содержание HD410

















Отзывы: