Bridgeview BALE KING 7400 Скачать руководство пользователя страница 36

Страница: 36 / 102

Bridgeview Manufacturing Inc.

Page 32

Cylinder Maintenance

The hydraulic cylinders are easily removed for repair or

maintenance simply by:

•

Lowering the fork (or deflector) to the down

position and unhooking the hydraulic lines. Be sure

there is no pressure on the lines and mark the line

locations so there is no confusion when reinstalling

the cylinders. Check hydraulic schematics.

•

Removing the cotter pin closest to the frame of the

machine and sliding the cylinder pins out

•

To reinstall, reverse the removal procedure

NOTE: Always cover exposed cylinder shafts with grease to avoid rusting of shafts if the unit is

not used for extended periods of time. Rusted cylinder shafts are NOT covered by warranty

NOTE: Check all hoses and fittings periodically for leaks. Tighten or replace any dripping

components or any worn out hoses.

Содержание BALE KING 7400







































































































Результаты поиска

Содержание BALE KING 7400

Отзывы:

Бренды по названию

Популярные бренды

Bridgeview BALE KING 7400, Руководство оператора

Результаты поиска

Содержание BALE KING 7400

Отзывы:

Бренды по названию

Популярные бренды