Bridgeview BALE KING 7400 Скачать руководство пользователя страница 25

Страница: 25 / 102

Bridgeview Manufacturing Inc.

Page 21

Optional Diverter Kit

The Bale King 7400 processor has an optional diverter kit which allows it to operate using only 2

hydraulic remotes. The fork and deflector functions are then controlled by a cab-mounted switch box.

This box must be wired up to the tractor. You may use the provided plug to plug into the accessory

outlet. If this is not available, the plug can be disassembled, and wired as necessary.

Black Wire

White Wire

+12V (Ignition

Switched)

-12 V / Ground

7400

Diverter Kit (3 – 2 Remote)

33769

7400X

Diverter Kit (4 – 3 Remote)

33771

7400X

Diverter Kit (4 – 2 Remote)

33772

A 4-pin plug is used to power the diverter valve on the processor. Route the plug to the rear end of

the tractor so the trailer end can be plugged in. If no power is supplied, the hydraulics will still control

the rear forks, but the deflector will not be functional. If the switch in the tractor is activated, the

deflector can be controlled. On 7400 machines with the option, this box can also control the 3-bale

clamp (as “Auxiliary”).

The diverter kit also features a pilot operated check valve to ensure that the deflector will not

fall down due to leaking across the valve.

Содержание BALE KING 7400







































































































Результаты поиска

Содержание BALE KING 7400

Отзывы:

Бренды по названию

Популярные бренды

Bridgeview BALE KING 7400, Руководство оператора

Результаты поиска

Содержание BALE KING 7400

Отзывы:

Бренды по названию

Популярные бренды