Bridgeview BALE KING 7400 Скачать руководство пользователя страница 13

Страница: 13 / 102

Bridgeview Manufacturing Inc.

Page 9

PTO Use and Maintenance

Shut

OFF

the tractor engine and remove the key before doing any maintenance on the machine. Use

ONLY genuine

Weasler

parts when replacing any worn or damaged PTO components.

Length:

Confirm the minimum and maximum working lengths of the drive-line.

The telescoping tubes must overlap at least 1/3 of their length when in

use. The PTO is designed to be used with a drawbar length of 16" from

the end of the PTO shaft. Adjust your tractor accordingly.

Shielding:

Be sure that the shielding is not damaged and

rotates freely on the drive shaft.

Working Angles:

Constant Velocity joints can operate up to 80 degrees for short

periods of time. Do not operate for long periods on sharp angles.

Attachment:

Be sure the drive-line is properly attached and all bolts and screws

are tight on the implement input shaft and on the tractor PTO shaft.

Storage:

When not in use, cover or protect the drive shaft from the weather.

When removed from the machine store both halves together to

prevent damage. Check all components for proper function and lubrication before use.

Содержание BALE KING 7400







































































































Результаты поиска

Содержание BALE KING 7400

Отзывы:

Бренды по названию

Популярные бренды

Bridgeview BALE KING 7400, Руководство оператора

Результаты поиска

Содержание BALE KING 7400

Отзывы:

Бренды по названию

Популярные бренды