Bridgeview BALE KING 7400 Скачать руководство пользователя страница 15

Страница: 15 / 102

Bridgeview Manufacturing Inc.

Page 11

Hydraulics

WARNING

Pressurized hydraulic fluid can cause serious injury.

•

When working with hydraulic equipment, eye and hand

protection should be worn.

•

Do not test for leaks with bare hands.

•

Relieve any pressure before removing a hose or fitting.

•

Never work under components raised by hydraulic

equipment unless supported externally.

There are three sets of hydraulic hoses to connect to the tractor. Each hose has a coloured marker to

identify its function. They should be connected at best convenience for the tractor's controls. Note

that the hoses are paired by colour and the following tables show the operation when pushing oil into

the hose with the longer marker.

7400 – 3 Remote

Long Blue

Lift rear fork

Long Red

Slats towards rotor

Long Yellow

Lift deflector

An optional diverter kit is available to allow the Bale King 7400

to run using only two sets of hoses. The function is then determined by

a control box, mounted in the cab of the tractor.

7400

Optional Diverter Kit

33769

7400 – 2 Remote

Control Box

“FORK”

“DEFLECTOR”

Long Blue

Lift rear fork

Lift deflector

Long Red

Slats towards rotor

Maintaining proper slat speed ensures consistent and smooth feeding of the bale into the roller.

Always set the tractor's hydraulic flow at a lower rate and adjust it upward until the desired speed is

reached. Place a bale in the tub without the rotor running. Rev the tractor up to PTO RPM. Turn the

bale counter-clockwise using the chain and slats. Adjust the hydraulic speed so that the bale makes

one full revolution in 8 to 10 seconds.

Содержание BALE KING 7400







































































































Результаты поиска

Содержание BALE KING 7400

Отзывы:

Бренды по названию

Популярные бренды

Bridgeview BALE KING 7400, Руководство оператора

Результаты поиска

Содержание BALE KING 7400

Отзывы:

Бренды по названию

Популярные бренды