Bresser 4Cast PC, Инструкция по эксплуатации

Страница: 55 / 64

55
2.7 WIRELESS OUTDOOR RAIN GAUGE
The Main Unit records the total amount of rainfall for the last hour, last 24 hours, yesterday, last
week and last month. The rainfall may be displayed in mm or inches.
A daily rainfall alert function is available which can be programmed to sound if the daily
rainfall exceeds a pre-configured limit.
ACCESSING RAIN GAUGE READING
From the main console unit: Press [ ] or [ ] until the RAIN icon on the display starts
flashing.
VIEWING RAIN STATISTICS
Each press of [ SET ] or [ MEMORY ] rotates display between different rain statistics:
• Last hour
• Last 24 hour
• Yesterday
• Last week
• Last month
Tip: For an estimation of the rain rate, the Last Hour rainfall value can be understood as
“inch/hr” or “mm/hr”.
RESETTING THE RAINFALL STATISTICS MEMORY
Press and hold [ MEMORY ] to reset all rainfall statistics.
SETTING UNITS FOR RAIN DISPLAY (INCH OR MM)
Press and hold [ SET ] to convert units between mm and inches.
ACTIVATING/DEACTIVATING THE DAILY RAINFALL ALERT
1. Each press of [ ALARM/CHART ] rotates display between the current rainfall statistics and
the daily rainfall alert (“ALARM HI” will be displayed).
If the alert is deactivated, “OFF” will be shown, otherwise the rainfall alert value is shown.
2. When the rainfall alert is displayed, pressing [ ] or [ ] will activate/deactivate it.
SETTING UP THE DAILY RAINFALL ALERT
1. Press [ ALARM/CHART ] to display rainfall alert.
2. Press and hold [ ALARM/CHART ] until rainfall alert and “ALARM HI” starts flashing in
the display.
3. Set Value for Rainfall Alert:
Press [ ] or [ ] to adjust value. Press and hold either button for fast advance.
Press [ ALARM/CHART ] to confirm your selection.
4. Upon completion the display will be returned to the rainfall alert display.
DISABLING WHEN DAILY RAINFALL ALERT IS ACTIVATED
To Disable Rainfall Alert:
Press [ ALARM/CHART ] to disable the alert.
2.8 WIRELESS OUTDOOR ANEMOMETER (WIND SENSOR)
The wind direction is shown by an animated compass display. Its angle can be displayed as
compass points (i.e. NW) or in bearings from the north (i.e. 22.5º).
The upper left of the wind display can be set to indicate the temperature at the anemometer or
the temperature adjusted with a wind chill factor.
The lower left of the wind display indicates the average wind speed for the last 10 minutes, as
well as gust, wind speed alert and gust alert information. It can also show records of the
maximum values of wind speed and gust attained for the current day.
The wind speed and gust alert functions can be programmed to sound if the wind speed or gust
exceeds a pre-configured limit. The wind speed may be displayed in km/h, mph, m/s or knots.
Note: The wind speed alert has a 5 mph hysteresis and the wind gust speed alert has a 7 mph
hysteresis. The hysteresis is to prevent the alerts from sounding constantly due to small
fluctuations near the alert value. This means that after the wind speed reaches the alert value, it
will have to fall below the alert value plus the hysteresis to deactivate the alert.
ACCESSING WIND MODE
Press [ ] or [ ] until the WIND icon on the display starts flashing.
CONFIGURING WIND DISPLAY
Each press of [ SET ] rotates display between:
• Temperature with wind chill, wind direction in bearings
• Temperature with wind chill, wind direction in compass points
• Temperature at anemometer, wind direction in compass points
• Temperature at anemometer, wind direction in bearings
SETTING UNITS FOR WIND SPEED DISPLAY (KM/H , MPH, M/S OR KNOTS)
Press and hold [ SET ] to convert wind speed units between km/h, mph, m/s or knots.
VIEWING WIND STATISTICS
Each press of [ MEMORY ] rotates wind speed display between:
• Current wind speed
• Daily maximum wind speed (“DAILY MAX” is displayed)
• Gust speed (“GUST” is displayed)
• Daily maximum gust speed (“GUST DAILY MAX” is displayed)
RESETTING THE WIND STATISTICS MEMORY
Press and hold [ MEMORY ] to reset all wind statistics.