6
7
en
en
is detected, and after it was dropped, unplug the unit
and apply to the service center.
•
Transport the kettle in the original package.
•
keep the unit out of reach of children and disabled
•
persons.
ELECTRIC KETTLE IS INTENDED FOR HOUSEHOLD
USE ONLY, DO NOT USE THE KETTLE FOR ROOM
HEATING, FOR INDUSTRIAL OR LABORATORY
PURPOSES
BEFORE USING THE KETTLE
After unit transportation or storage at low
temperature, it is necessary to keep it for at least
three hours at room temperature.
•
Unpack the kettle and remove all the packaging
materials.
•
keep the original package.
•
Check the delivery set.
•
Read the safety measures and operating
recommendations.
•
examine the kettle for damages, in case of damage
do not plug it into the mains.
• Make sure that the specifications of power supply
voltage specified on the lower panel of the unit or
the base correspond to the specifications of your
mains. When using the kettle in the mains with 60
Hz frequency, the unit does not need any additional
settings.
ATTENTION!
Be careful while handling the kettle, glass flask can
break when the kettle is dropped or hit against a solid
object.
• Place the base (1) on a solid steady flat and non-slip
non-metal surface away from heat sources as far as
possible from the edge of the surface.
•
do not place and do not use the kettle in closed
space, for example, in the cupboard or in closed
structures — this can lead to its breakage, cause
harm to the user or damage to his/her property.
• Wash the flask (2) with neutral detergents, rinse and
dry. Wipe the outer surface of the flask (2) with a
slightly damp cloth and then wipe it dry. do not use
abrasives and coarse scourers for this.
•
Before connecting the kettle, make sure that there
are no moisture drops on the base (1), the flask (2),
the power cord and the power plug.
•
Remove the kettle from the base (1).
• To fill the kettle with water press the lid opening
button (6) and open the lid (5).
•
Fill the kettle with water up to the «MAX» mark,
according to the scale situated on the outer surface
of the flask (3).
•
Wipe the base (1), the outer and inner surfaces of the
flask (2) with a clean, slightly damp cloth to remove
dust.
•
Close the lid, make sure that the kettle lid is closed
tightly.
•
Place the kettle on the base (1).
•
Insert the power plug into the mains socket.
•
Press the On/Off button (11) « ». you will hear a
sound signal, the flask illumination (2) will light up,
the process of boiling will start. In the process of
heating the flask illumination (2) will change its color.
•
After water starts boiling you will hear sound signals,
the flask illumination (2) will go out, the kettle will
pass into standby mode (there is no indication).
•
If it is necessary to switch the kettle off, press the On/
Off button (11) « » or remove the kettle from the
base (1).
•
Remove the kettle from the base and carefully pour
out boiled water into a suitable bowl.
•
Remember that there is boiling water inside the kettle
flask (3), always hold the kettle only by the handle
(8), do not tilt the kettle sharply, in case of careless
use of the kettle you can get burns by hot water.
•
Repeat the water boiling procedure several times.
• Hot water resulting from the first boilings is not
recommended to consume, you may use it for
domestic needs.
ATTENTION!
To avoid burns by hot steam, do not bend over the
spout (4).
USING THE ELECTRIC KETTLE
Place the kettle on a solid steady flat and non-slip
non-metal surface away from heat sources as far as
possible from the edge of the surface.
WATER BOILING
• To fill the kettle with water press the lid opening
button (6) and open the lid (5).
•
Fill the kettle with water not below the mark «MIn»
and not above the maximal mark «MAX».
•
Close the lid (5) and put the full kettle on the base
(1).
•
Insert the power plug into the mains socket.
•
Press the On/Off button (11) « ». you will hear a
sound signal, the flask illumination (2) will light up,
the process of boiling will start. In the process of
heating the flask illumination (2) will change its color.
•
After water starts boiling you will hear sound signals,
the flask illumination (2) will go out, the kettle will
pass into standby mode (there is no indication).
•
Press the On/Off button (11) « » and hold it within
3 seconds, you will hear a sound signal, the flask
illumination (2) will light up red. After water starts
boiling, the kettle will maintain the water temperature
within 2 hours, the illumination (2) will be glowing red.
Water heating will switch on, if the water temperature
cools down to 85°.
Содержание BR1021
Страница 23: ...brayer su ...
