Brave VH0934 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 48

background image

✔

ALWAYS check the oil level in the hydraulic oil tank and engine reservoir.

✘

NEVER operate your log splitter when it is in need of repair or is in poor
mechanical condition.

✘

NEVER tamper with the engine to run it at excessive speeds. The maximum
engine speed is preset and is within safety limits.

✘

NEVER make alterations to your log splitter in any manner. Such alterations
may cause the log splitter to become unsafe and WILL VOID THE WARRANTY.

✘

NEVER attach a rope or extension to the control lever or add width or height to
the splitting wedge. Such ALTERATIONS may cause the log splitter to become
UNSAFE and WILL VOID THE WARRANTY.

✘

ALWAYS clean the unit after each use. If possible, store the unit inside or cover
it completely, if stored outside.

Towing

✔

ALWAYS check before towing to make certain your log splitter is correctly and
securely attached to the towing vehicle. Be sure that the ball hitch you are
using is the proper size for the hitch coupler on the log splitter (see “Specifi-
cation” section). Be sure the safety chains are properly hooked to the vehicle
leaving enough slack for turning.

✔

ALWAYS allow for added length of the log splitter when turning, parking, cross-
ing intersections, and in all driving situations.

✔

ALWAYS be careful when backing up. You could jackknife your log splitter if
care is not taken.

✔

ALWAYS disconnect your log splitter from your towing vehicle before attempt-
ing to use it.

✘

NEVER exceed 35 m.p.h. when towing your log splitter. Obey all state and
local regulations when towing on state and local roads and highways. Adjust
your speed for terrain and conditions, as needed. Be extra cautious when tow-
ing over rough terrain, especially over a railroad crossing.

✘

NEVER tow your log splitter when there is fuel in the engine’s tank.

✘

NEVER allow anyone to sit or ride on your log splitter.

✘

NEVER carry any cargo or wood on your log splitter.

815-672-8861

7

Brave Products, Inc.

«
...
7
8
9
10
11
...
»

Содержание VH0934

















































Отзывы:

Нет отзывов

Похожие инструкции для VH0934

Бренд: Swisher Страницы: 20

Бренд: Erskine Attachments Страницы: 16

Бренд: Forstmeister Страницы: 22

Бренд: EINHELL Страницы: 64

Бренд: Greyhound Страницы: 14

Бренд: Split-fire Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды