Brave VH0934 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 48

background image

3

. Start the engine using the instructions from

the engine manual. If the log splitter has
not been running (cold engine), warm up
the engine and hydraulic system by run-
ning the engine at half throttle for 3 to 4
minutes, then advance the engine throttle
control to maximum speed.

Operation – Horizontal Position

Before loading and operating the log splitter,
put on the proper protective gear such as
safety goggles, face shield, hearing protec-

tion, tight-fitting gloves (without draw strings or loose cuffs), and steel-toed
shoes.

4

. Use the following photos for the correct

and incorrect methods of splitting logs.
Never split a log using an incorrect or
unsafe method.

a

. Place the log on the log splitter. Grasp

the log on the sides, near the middle of
the block. Center the log, side-to-side
on the rail of the log splitter, making
sure that the sawed end is against the
large plate (end plate), opposite the
splitting wedge.

Do not place your hands on the
ends of the log when loading the
log splitter. This is a very

UNSAFE method and could result in injury
to your hands.

CAUTION

WARNING

815-672-8861

21

Brave Products, Inc.

«
...
21
22
23
24
25
...
»

Содержание VH0934

















































Отзывы:

Нет отзывов

Похожие инструкции для VH0934

Бренд: Pow’R’kraft Страницы: 17

Бренд: PowRkraft Страницы: 24

Бренд: ATIKA Страницы: 94

Бренд: Quality Craft Страницы: 34

Бренд: Omega Страницы: 76

Бренд: MTA Страницы: 19

Бренд: Lea Страницы: 74

Бренд: Generac Power Systems Страницы: 24

Бренд: Generac Power Systems Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды