Brave VH0934 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 48

background image

Operation – Vertical Position

Before loading and operating the log splitter,
put on the proper protective gear such as
safety goggles, face shield, hearing protec-

tion, tight-fitting gloves (without draw strings or loose cuffs), and steel-toed shoes.

5

. Use the following photos for the correct

and incorrect methods of splitting logs.
Never split a log using an incorrect or
unsafe method.

a

. To operate the log splitter in a vertical

position, pull the spring-loaded locking
lever and twist it in either direction to
lock it in the “unlocked” position.

NOTE:

Before raising the log splitter into a

vertical position, make sure the locking lever,
located by the hydraulic tank, is in the
unlocked position. Not following this recom-
mendation may result in damage to the
plunger.

b

. Block the wheels and stand the rail

assembly up into a vertical position.

c

. Turn the knob handle until the pin

slides into the slot. This allows the
plunger to snap into place, securing
the rail assembly in a vertical position.

WARNING

Brave Products, Inc.

24

815-672-8861

«
...
24
25
26
27
28
...
»

Содержание VH0934

















































Отзывы:

Нет отзывов

Похожие инструкции для VH0934

Бренд: EINHELL Страницы: 276

Бренд: Meec tools Страницы: 55

Бренд: Meec tools Страницы: 39

Бренд: Northern Industrial Tools Страницы: 8

Бренд: Swisher Страницы: 20

Бренд: Swisher Страницы: 20

Бренд: Swisher Страницы: 20

Бренд: Swisher Страницы: 20

Бренд: Swisher Страницы: 20

Бренд: Swisher Страницы: 20

Бренд: Dirty Hand Tools Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды