Braun 4195, Руководство пользователя

Страница: 5 / 35

Safety fuse
If the motor switch is turned on, but the motor sud­
denly stops or does not run, the built in safety fuse
has been activated. Should this happen, turn the
appliance off and wait until the motor has cooled off
(approximately 15 minutes).
If the motor will not start when switching it on again,
repeat the cooling off procedure (see above).
After use, turn off the appliance and unplug it.
also process fish, vegetables, onions, soaked bread
rolls, boiled potatoes, stoned plums for jam. Fill the
prepared meat or vegetables into the feeder tray © and
push it down into the filling shaft with the pusher ® .
Never use a fork, a spoon handle or a similar object.
If meat is crushed instead of being cut properly, please
check whether the meat grinder is assembled correctly
(e. g. whether you have perhaps over-looked inserting
one of the parts) or clean the blade © and disc 2 .
Before using
All parts of the grinder attachment were covered with a
lubricating film before leaving the factory. They must be
washed before using the first time (see «Cleaning»).
Assembly
- Please note the correct assembly order of
parts ® - © .
- The sharp side of the blade © must face the disc 2 .
- Guide the notch B in the disc 2 over the protrusion
© in the grinder head © .
- After assembling the parts 2 - 4 , screw the cap ®
moderately tight onto the grinder head © .
The assembled grinder head © is joined to the motor
unit © with a bayonet lock. Insert the metal housing into
the motor unit by holding the filling shaft of the grinder
head at an angle of 45° clockwise (the ^ marking on
the grinder head has to match the ^ marking on the
motor unit (A)). Turn the grinder head anti-clockwise in
the direction of the upright arrow (A) until the filling shaft
snaps into place in an upright position. Place the feeder
tray © on the filling shaft.
To remove the grinder head © press the release button
© and turn the grinder head clockwise 45° as shown in
picture B.
• In order to avoid any risk caused by the rotating
blade make sure that you only attach the grinder
head © to the motor part after it has been completely
assembled with disc, blade and worm.
• Before attaching / replacing accessories that are in
movement during operation, switch off the appliance
and unplug it.
Notice
• Before mincing frozen meat, defrost it to such a
degree that you can cut it into cubes of appropriate
size. These cubes can be processed with the
appliance.
• When processing food with high power consumption
- e. g. sunflower seeds mixed with oats at a ratio
of 1:3 (approximately 800 W) - do not exceed an
operating time of 10 seconds.
• Before using the «Kubbe» attachment © / Sausage
filler l , the meat has to be ground twice.
Cleaning
Wipe the motor unit © with a damp cloth only and wipe
it dry. All other parts can be washed in hot water with
normal dishwashing liquids.
Storage
There is a practical cord storage j at the base of the
unit (C).
Subject to change without notice.
Please do not dispose of the product in the
household waste at the end of its useful life.
Disposal can take place at a Braun Service
Centre or at appropriate collection points
provided in your country.
Operating
Turn on the motor before filling with meat, fish,
vegetables etc. To do so, press the on switch H so that
it engages.
To turn off the appliance, press the off switch h .
In case the appliance is clogged, stop it by pressing the
off switch h .
Then press the reverse button © (not longer than
10 seconds).
To continue mincing, press the on switch again.
Important: Wait until the appliance has stopped
completely before pressing the reverse button or the on
switch.
Before processing meat, remove tendons and bones
and cut it into strips. Besides meat, the machine will
6