background image

 

4

3 SECURITY PRINCIPLES 

3.1

 

SECURITY

 

PRINCIPLES

 

OVERVIEW 

A hazard exists when handling loads especially in the event that the jack is not use in the right 
way or is badly maintained. Whereas as a result an accident or severe injury could happen, it is 
necessary  to  observe  the  special  security  measures  when  handling,  assembling,  maintaining 
and checking the jack. 
 

!  WARNING 

ALWAYS 

ensure  the  load  against  drop  (i.e.  by  a  stand  or  jack  block),  if  you  are  going 
to work under it. 

NEVER   

burden the jack more than is the load capacity indicated on the jack. 

NEVER   

jack up persons. 

ALWAYS 

warn persons in surroundings before starting work. 

ALWAYS 

read the operational manual and security instructions. 

ALWAYS 

ensure  the  movement  of  load  raising  in  one  direction  i.e.  vertical  when 
manipulating with ISO containers. 

ALWAYS 

set up the jack vertically when manipulating with ISO containers. 

Bear in mind that the operation staff is responsible for faultless technique of raising loads. 
Hence verify all national directives, regulations and standards whether they contain other 
information on safety work with your jack. 

 

3.2.

 

SECURITY

 

PRINCIPLES 

 !  WARNING 

3.2.1 Prior to use 

ALWAYS 

ensure  the  jack  would  be  operated  by  physically  fit,  qualified  and  instructed 
persons older than 18 years, demonstrably familiarized with the operation manual 
and  trained  in  security  of  work  and  mode  of operation.  The  user  keeps 
demonstrably the registration of training persons.  

 

ALWAYS 

check  up  the  jack  every  day  before  starting  work  according  to  section  8.2.  (1) 
„Daily inspection“. 

 

ALWAYS 

make sure that the lift is adequate for intended work.  

ALWAYS 

respect the jack is on firm foundation. 

NEVER 

jack up loads well set or of unknown weight. 

NEVER 

push with the jack without knowledge of expansion forces. 

NEVER

  

use the defective or outworn jack. 

NEVER 

use the jack without visible load capacity marking on the jack. 

NEVER 

use the jack marked with the label „

OUT OF OPERATION

“. 

ALWAYS 

consult  the  producer  or  his  authorized  representative  any  application  of the  jack 
in nonstandard or extreme environment. 

Содержание 15-00-CM



















Отзывы: