background image

 

IMPORTANT

Before proceeding, please inspect the 

water heater and its components for 

possible damage.

DO NOT

install any 

water heater with damaged 

components. If damage is evident 

then please contact the supplier where 

the water heater was purchased or the 

manufacturer listed on the rating plate 

for replacement parts.

 

 

 

DANGER 

DO NOT store or use gasoline or 

other flammable, combustible, or 

corrosive vapors and liquids in the 

vicinity of this or any other appliance

.

WARNING 

DO NOT ATTEMPT TO LIGHT ANY GAS APPLIANCE 

IF YOU ARE NOT CERTAIN OF THE FOLLOWING:

x

Liquefied petroleum gases/propane gas and 

natural gas have an odorant added by the gas 

supplier that aids in the detection of the gas.

x

Most people recognize this odor as a “sulfur” or 

“rotten egg” smell.

x

Other conditions, such as “odorant fade” can 

cause the odorant to diminish in intensity, or 

“fade”, and not be as readily detectable.

x

If you have a diminished sense of smell or are in 

any way unsure of the presence of gas, 

immediately contact your gas supplier from a 

neighborʼs telephone.

Gas detectors are available.  Contact your gas 

supplier, or plumbing professional, for more 

information.

WARNING 

FAILURE TO INSTALL AND MAINTAIN A NEW, 

LISTED 3/4” X 3/4” TEMPERATURE AND PRESSURE 

RELIEF VALVE WILL RELEASE THE 

MANUFACTURER FROM ANY CLAIM THAT MIGHT 

RESULT FROM EXCESSIVE TEMPERATURE AND 

PRESSURES.

CAUTION 

If sweat fittings are to be used DO NOT apply heat to 

the nipples on top of the water heater.  Sweat the tubing 

to the adapter before fitting the adapter to the water 

connections.  It is imperative that heat is not applied to 

the nipples containing a plastic liner.

WARNING 

Water heaters are heat producing appliances.  To 

avoid damage or injury, do not store materials 

against the water heater or vent-air intake system.  

Use proper care to avoid unnecessary contact 

(especially by children) with the water heater and 

vent-air intake components. UNDER NO 

CIRCUMSTANCES SHOULD FLAMMABLE 

MATERIALS, SUCH AS GASOLINE OR PAINT 

THINNER BE USED OR STORED IN THE 

VICINITY OF THIS WATER HEATER, VENT-AIR 

INTAKE SYSTEM OR IN ANY LOCATION FROM 

WHICH FUMES COULD REACH THE WATER 

HEATER OR VENT-AIR INTAKE SYSTEM.

WARNING 

Hydrogen gas can be produced in an operating 

water heater that has not had water drawn from the 

tank for a long period of time (generally two weeks 

or more). HYDROGEN GAS IS EXTREMELY 

FLAMMABLE. To prevent the possibility of injury 

under these conditions, we recommend the hot 

water faucet to be open for several minutes at the 

kitchen sink before you use any electrical appliance 

which is connected to the hot water system. If 

hydrogen is present, there will be an unusual sound 

such as air escaping through the pipes as hot water 

begins to flow. DO NOT smoke or have open flame 

near the faucet at the time it is open.

– WHAT TO DO IF YOU SMELL GAS

x

Do not try to light any appliance.

x

Do not touch any electrical switch; do not use any 

phone in your building.

x

Immediately call your gas supplier from a neighborʼs 

phone. Follow the gas supplierʼs instructions.

x

If you cannot reach your gas supplier, call the fire 

department.

– Installation and service must be performed by a qualified

installer, service agency, or the gas supplier. 

WARNING:

If the information in these instructions is not followed 

exactly, a fire or explosion may result in property damage, personal 

injury, or death.

For Your Safety

Do not store or use gasoline or other flammable, combustible, or 

corrosive vapors and liquids in the vicinity of this or any other 

appliance.

3

Содержание RG130T*X Series













































Отзывы: