background image

14 

Troubleshooting continued-

 

 

LED Status

Control Status

Probable Cause

Six  f lashes,  t w o 

f lashes, three 

second pause 

(Sof t   Lockout )

Relay not  w orking properly 

during burner operat ion, 

syst em aut o reset s aft er 

(5) minut es

Fault y relay

Six  f lashes,  t hree 

f lashes, three 
second pause 

(Sof t  Lockout )

Pilot  f lame ext inguished, 

syst em aut o reset s aft er 

(5) minut es

1. Unst able pilot
2. Pilot  t ube block or restrict ed
3. Oxidat ion build-up on pilot  elect rode
4. Wire damage to pilot  assembly or bad 
connect ion at  gas valve
5. Insuf f icient   combust ion  air

Six f lashes, f our 

f lashes, three 
second pause

Undesired f alse pilot  f lame 

sensed, syst em auto 

resets

Pilot  valve st uck in open posit ion

Seven f lashes, 

three second 

pause

Flammable vapor sensor or 

reset t able  t hermal  sw it ch 

f ault   det ect ed,  see 

w arning label

1. Flammable vapor present
2. Flammable vapor sensor exposed t o 
excessive moist ure
3. Flammable vapor sensor exposed t o 
ext reme ambient  t emperat ure
4. Reset t able  t hermal  sw it ch  open

Eight  f lashes, one 

flash, t hree 

second pause

Flammable vapor sensor 

out  of  specif icat ion, 

possible short

1. Flammable vapor sensor out  of  
specif icat ion
2. Possible short  in f lammable vapor sensor 
or reset t able  t hermal  sw itch  w iring

Eight  f lashes, 

t hree  f lashes, 

three second 

pause

Thermal w ell sensor 

damaged or unplugged or 

gas valve electronics fault  

det ected

1. Damage t o t hermal w ell w ires
2. Thermal w ell sensor resist ance out  of 
range
3. Replace t hermal w ell
4. Verif y cont rol is not  w et  or physically 
damaged
5. Reset   cont rol  on/of f   sw it ch
6. Replace elect ronic module if  8-3 error 
persist s

Eight  f lashes, f our 

f lashes, three 

second pause

Gas  valve  f ault   det ect ed

1. Verif y cont rol is not  w et  or physically 
damaged
2. Reset   cont rol  on/of f   sw it ch
3. Replace gas cont rol if  8-4 error persist s

 

 

Fault Probable 

Cause 

Resettable Thermal Switch Tripped (Open) 

1.  Insufficient combustion air 
2.  Flammable vapors present 

 

Содержание Defender Safety System 238-48248-00

















Отзывы: