Bozzio Joysteer Generation 1.0 Скачать руководство пользователя страница 48

Страница: 48 / 56

Universal System Manual

Bozzio AG * joysteer®

page 48 of 56

Message on display

Troubleshooting

Description and criteria for error

Error X

069

SAM poti

•

Check cable

•

Replace SAM

One of the potentiometers are defective.

If one of the two SAM potentiometer differs more than 90° to the SAM encoder
position.

Error X

070

BAM Overload

•

Average brake force is to high

•

Apply correct brake force

•

Check parameter "Overload Time"

Brake actuator motor overload

𝑖

𝑜𝑣𝑒𝑟𝑙𝑜𝑎𝑑

= 16𝐴

𝑡

𝑜𝑣𝑒𝑟𝑙𝑜𝑎𝑑

= 𝑃(𝐵𝐴𝑀 → 𝑂𝑣𝑒𝑟𝑙𝑜𝑎𝑑 𝑇𝑖𝑚𝑒)

𝑖

𝑠𝑢𝑚

= ∑ 𝐼

𝐵𝐴𝑀

𝑡

𝑜𝑣𝑒𝑟𝑙𝑜𝑎𝑑

𝑖

𝑠𝑢𝑚

> 𝑖

𝑜𝑣𝑒𝑟𝑙𝑜𝑎𝑑

∗ 𝑡

𝑜𝑣𝑒𝑟𝑙𝑜𝑎𝑑

Error X

071

EOL

•

End of life is reached

The system was running more than 490000 km or was used longer than 8200h.

Error X

072

Temp

•

Check the temperature of the converter modules

•

Check if there is hot air blown on the converter modules

The controller board or the converter board temperature is higher than 70°C.

Error X

073

EAM Speed to high

•

Adjust speed between Servicemanager and car speed

Speed is higher than 220km/h

Error X

074

EAM No Speed Signal

•

Check Speed sensors or CAN Adapter

No speed signal longer than 10min.

Error X

075

BAM Stroke to big

•

Readjust Brackets

Stroke has to be shorter than 80 mm

Error X

076

EAM Test

•

Charge the backup-battery

•

Set parameter “Minimal drop pulse test [mV]” to zero.
Restart.
If the Error is disappeared, then the Pulse test box is defective

Test of backup-battery failed

At the beginning of the pulse test:

(𝑢

𝑅𝑒𝑙𝑎𝑦1

+𝑢

𝑅𝑒𝑙𝑎𝑦2

)

> 2𝑉 (6𝑉 𝑖𝑓 𝑡𝑒𝑚𝑝 > 60°)

𝑎𝑏𝑠𝑜𝑙𝑢𝑡𝑒(𝑢

𝑏𝑎𝑐𝑘𝑢𝑝

− 𝑢

𝑝𝑢𝑙𝑠𝑒

) < 𝑃(𝐸𝐴𝑀 → 𝑚𝑖𝑛𝑖𝑚𝑎𝑙 𝑑𝑟𝑜𝑝 𝑝𝑢𝑙𝑠𝑒 𝑡𝑒𝑠𝑡)

Error X

129

Plug

•

Check if board- and backup-battery are connected and charged.

•

There is a wrong converter module connected, Make sure S1 is at

connector X31 & X32 and S2 is at connector X41 & X42

•

Wrong software installed, reinstall the correct software for S1 &

Module plugged incorrectly

𝐼𝐷

𝐻𝑊

≠ 𝐼𝐷

𝑆𝑊

Error X

130

SSM Overload

•

Average feedback torque is to high

Steering sensor motor overload

Содержание Joysteer Generation 1.0

























































Результаты поиска

Содержание Joysteer Generation 1.0

Отзывы:

Bozzio Joysteer Generation 1.0, Руководство пользователя, Страница: 48 / 56

Результаты поиска

Содержание Joysteer Generation 1.0

Отзывы: