Bowflex TreadClimber TC5 Скачать руководство пользователя страница 1

1

Important Safety Instructions - Before servicing or using this equipment, obey the following warnings:

This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury. Read and understand all Warnings on this machine.

004-4704-011512.A

Service manual

• Read and understand the Service Manual before working on the machine. Failure to obey the instructions and safety warnings could cause injury to the service technician or by

-

standers. • Keep bystanders and children away from the product being serviced at all times. • Make sure that the repair is done in an appropriate work space away from foot traffic 

and exposure to bystanders. • Disconnect all power (batteries) and allow to sit for 5 minutes before you service this machine. • Some components of the equipment can be heavy or 

awkward. Enlist the service of a second person when you do maintenance steps involving these components. Do not try to do heavy or awkward steps on your own. • Use only re

-

placement parts and hardware that are supplied or approved by Nautilus. Failure to use Nautilus-approved replacement parts can adversely affect the safety and functionality of the 

equipment creating a risk to users. • Be sure that all warning stickers and instructional placards applied to the product stay present and in good condition when doing maintenance 

or replacing components. If necessary request replacement warning stickers or placards from Nautilus

®

 customer service. • Do not try to change the design or functionality of the 

machine being serviced as this can adversely effect user safety. • Do not use the machine until all shrouds, instructions, warning labels and correct functionality have been verified 

and tested for correct performance.

Nautilus, Inc., (800) NAUTILUS / (800) 605-3369, www.NautilusInc.com - Customer Service: North America (800) 605-3369, tcinquiry

@nautilus.com

 | outside U.S. +01-360-859-5180, [email protected] | © 2011 Nautilus, Inc., 

All rights reserved. ™ and ® indicate a trademark or registered trademark. Nautilus, Inc. (www.NautilusInc.com) trademarks include NAUTILUS®, BOWFLEX®, SCHWINN® and UNIVERSAL® and respective logos. Other trademarks are 

the property of their respective owners.

Specifications

   Assembled Weight:   

approx. 163 lbs. (74 kg)

   Power Requirements:  

2 AA batteries (not included)

   Operational Voltage: 

1.0 - 3.3VDC

   

Serial Number

   AAAAAAA 

 

Nautilus

®

 part number (SKU)

   BBB 

 

 

Vendor Code

   PPPPPP   

 

Purchase Order Number

   LL 

 

 

Purchase Order Line Number

   CCCCCC  

 

Unique Identifier

®

®

TreadClimber

® 

by Bowflex

®

 TC5 Fitness Machine

Important Safety Instructions 

 

 

1

Specifications 

 

 

 

1

Care of the Fitness Machine 

 

 

2

Walking Belt and Deck Lubrication   

 

2

Walking Belt Adjustment 

 

 

2

Walking Belt Electrostatic Reduction 

 

3

Troubleshooting  

 

 

 

4

Console Service/Setup Mode 

 

 

5

Replacing the Console Top with Electronics Assembly  6

Replacing the Console Assembly / Console Shroud 

7

Replacing the Drive Belt 

 

 

8

Removing the Treadle Assembly   

 

10

Replacing the Walking Deck 

 

 

14

Replacing the Front Roller 

 

 

17

Replacing the Walking Belt 

 

 

19

Replacing the Dependency 

 

 

24

Replacing the Main Drive Assembly 

 

26

Replacing the Speed Sensor Cable 

 

30

Содержание TreadClimber TC5


































Отзывы: