Boston Whaler 240 Outrage Скачать руководство пользователя страница 38

Страница: 38 / 44

Section 9 - Getting to know your Boston Whaler

240 Outrage-Owners Manual

Hull Maintenance

Clean the bottom of your boat of marine growth im-

mediately, if the debris dries it will harden and will

make its removal very difficult.Waxing of the exte-

rior surfaces is recommended to be done at least twice

a year to protect the gelcoat of your boat. Com-

pounding may be neccessary to remove more stub-

born stains and chalking from the surface of your

boat, compounding must be done after washing and

prior to waxing. Check with your Boston Whaler ®

dealer on a compatible rubbing compound for your

boat. When washing your windshield never use abra-

sive powders, gritty cloths or steel wool. Always

use a damp cloth or a chamois when drying. Metal

trim and fittings will stay bright if coated with a good

grade metal polish or paste wax after washing. Stain-

less steel is strong and corrosion resistant, but still

requires maintenance to keep its appearance. Crev-

ice corrosion, a brownish coloring; occurs where two

pieces of stainless hardware meet.

This condition is caused by impurities in water and

air and can be cleaned easily with a good grade ma-

rine polish using a sponge, cloth or small bristled

brush (for nooks and crannies).

Hull Maintenance, (Blisters)

The fiberglass and resin structure of your boat is

porous (intrusion of water into the gelcoat will take

some time). Blistering is caused by water soluble

materials in the hull laminate. The effect of osmotic

pressure allows water to impregnate below the

gelcoat and substrate; forming a blister. There have

been extensive university studies funded by the

United States Coast Guard regarding the cause and

effect of blisters forming in the gelcoat of fiberglass

boats. Fiberglass blisters can form in near-surface

layers of the gelcoat to very deep into the fiberglass

structure. The damage can range from cosmetic to

catastrophic, (although the latter is a very rare

occurance). The studies seemed to point toward long

term immersion of the hull in warm water as a pri-

mary cause of hull blisters. Stress cracks on the hulls

below the waterline also contributed to the forma-

tion of blisters on the hull. There are a variety of

ways to prevent the formation of hull blistering: Ep-

oxy coatings can be applied to the hull, followed by

hull painting.

An alkyd-urethane-silecone marine paint can also be

used to aid in the prevention of hull blisters.

Reducing the amount of time that your boat stays in

the water also helps prevent hull blisters from form-

ing. Use of a trailer or boat lift will reduce the

liklihood of hull blisters forming. Be sure to use a

bunk type lift or trailer for long term storage of the

boat out of water. If blisters are present in the hull;

they need to be properly cleaned and dried out be-

fore any barrier protection can be applied. Contact

your Boston Whaler® dealer for more information

on prevention and treatment of hull blisters.

Bottom Painting

Painting the bottom of your boats hull is a good way

to slow the formation of hull blisters, and also keep-

ing bottom growth (fouling) under control. To deter-

mine the waterline, you will need to place the boat

in water and with a full load of fuel and gear, mark

the waterline. Measure above the marked line 1 to 3

inches for placement of the tape line. Masking tape

is not recommended for the types of paint you will

be using. Preparation is the key to a successful hull

painting. If the hull is bare, the gelcoat will have to

be dewaxed before sanding can begin;otherwise the

wax will be dragged into the scratches and will re-

duce the adhesion properties of the paint. After the

dewaxing is complete, light sanding with 80 grit pa-

per is recommended. Proper ventilation and capture

of the dust created by sanding is essential. The dust

created is toxic and should not be breathed. A proper

fitting respirator must be used. DO NOT use a paper

filter mask. The paint can be applied after sanding

and cleaning is complete. Follow the manufacturers

recommendation for applying the paint. Humidity and

weather will play a role in how and when the paint is

applied. Several thin layers are better than one thick

layer.

DANGER

There are risks and dangers inherent with the use of

paints and solvents. Dispose properly of all rags, roll-

ers and trays used for painting. Follow all the precau-

tions and regulations listed by the manufacturer before

and after painting your boats hull.

Содержание 240 Outrage













































Результаты поиска

Содержание 240 Outrage

Отзывы:

Похожие инструкции для 240 Outrage

Бренды по названию

Популярные бренды

Boston Whaler 240 Outrage, Руководство пользователя

Результаты поиска

Содержание 240 Outrage

Отзывы:

Похожие инструкции для 240 Outrage

Бренды по названию

Популярные бренды