Boston Whaler 20 Justice Series Скачать руководство пользователя страница 62

Страница: 62 / 140

3-8

Section 3

Fuel Systems

Fuel Gauge and Sending Unit

The fuel tank has a sending unit that sends fuel level

information to the electric fuel level gauge installed on

the control console. The fuel level sender is an

ISSPRO

unit. The sending unit is fully electronic and

compatible with Mercury Marine’s SmartCraft gauge

system. The sending unit generates a fuel level signal

between 240 ohms (empty) and 33 ohms (full).

The fuel gauge powers up when the engine ignition

key switch is turned to the ON position. The fuel

gauge displays the approximate

fuel level in the fuel

tank. The correlation between the gauge reading and

the fuel load is approximately linear from

FULL

. The accuracy of the reading decreases below

FULL

because of the tank’s profile.

The most accurate fuel level reading is obtained when

the boat is at rest and level.

CAUTION

The fuel gauge reading is approximate.

Confirm the gauge reading using other

methods. Be conservative when estimating fuel

on-board.

Содержание 20 Justice Series












































































































































Результаты поиска

Содержание 20 Justice Series

Отзывы:

Похожие инструкции для 20 Justice Series

Бренды по названию

Популярные бренды

Boston Whaler 20 Justice Series, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 20 Justice Series

Отзывы:

Похожие инструкции для 20 Justice Series

Бренды по названию

Популярные бренды