Boston Whaler 20 Justice Series Скачать руководство пользователя страница 46

Страница: 46 / 140

2-24

Section 2

Boat Operation

Trailering

If Boston Whaler supplied the trailer for your boat, it is

designed specifically for your boat and it is commer-

cial-grade. The trailer construction is heavy-duty and

it exceeds the capacity requirements for your boat.

This trailer might be equipped with additional

upgrades to suit your mission.

Regulations controlling trailer equipment and manu-

facture vary from place to place. You must verify that

your trailer meets the laws and transportation regula-

tions in the states or countries where you use it.

Refer to the trailer owner’s manual for detailed infor-

mation about the operation and maintenance of this

trailer.

CAUTION

Do not trailer your boat with the engine in its

fully tilted position.

CAUTION

Center the engine before tilting to avoid contact

with any special towing equipment on your

boat.

Содержание 20 Justice Series












































































































































Результаты поиска

Содержание 20 Justice Series

Отзывы:

Бренды по названию

Популярные бренды

Boston Whaler 20 Justice Series, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 20 Justice Series

Отзывы:

Бренды по названию

Популярные бренды