Boston Whaler 20 Justice Series Скачать руководство пользователя страница 51

Страница: 51 / 140

2-29

Boat Operation

Section 2

Lifting and Slinging

Safety Warnings

WARNING

Verify that the lifting equipment, spreader bars,

slings, and attaching hardware are profession-

ally certified to a working load of at least 6,000

pounds (2722 kg) with a safety factor of five.

Failure of any lifting component could cause

extensive damage to the boat, serious injury, or

death.

DANGER

Never allow anyone to be in the boat or under

the boat while you are lifting it. A mistake in the

lifting procedure or a component failure could

cause serious injury or death.

DANGER

Inspect all lifting equipment for signs of wear or

fatigue each time you lift the boat. Re-certify or

replace the lifting equipment annually. Failure

of any lifting component could cause serious

injury or death.

WARNING

Never use the boat’s bow eye, stern eyes,

cleats, or railings as attachment points to lift

this boat. Failure of these items during lifting

could cause extensive damage to the boat,

serious injury, or death.

CAUTION

Before you lift your boat, inspect the bottom to

determine if there are any thru-hull transducers

installed. Contact between lifting gear and a

transducer will cause immediate, extensive

damage to the transducer and the hull.

Содержание 20 Justice Series












































































































































Результаты поиска

Содержание 20 Justice Series

Отзывы:

Похожие инструкции для 20 Justice Series

Бренды по названию

Популярные бренды

Boston Whaler 20 Justice Series, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 20 Justice Series

Отзывы:

Похожие инструкции для 20 Justice Series

Бренды по названию

Популярные бренды