background image

21

Press 'SELECT' to exit setting of 'dt' value.
If 'dt' is greater than  '00', the display will skip the 'tt' 
option and prompt for the 'Sr' setting.

Press 'SELECT' to exit setting of 'Sr' value. Display will 
prompt for SA setting.

Press 'SELECT' to return to normal operating mode. 
Count value is displayed

When using a single gate switch (DIP SW2 On) to enable 
the batch start, option 'SA' allows the choice of swit-
ching witch either of the following:

Press 'SELECT' to exit setting of 'tt' value. Display will 
prompt for Sr setting.

Optional 'dt' and 'tt' Cycle Time Alarms. other misc options

Two optional alarms are provided to alert the operator if too much time is being taken to run the screws 
into the assembly. The 'dt' Standby Time Alarm can be set in 1 second intervals. It is the allowable time to 
run each screw cycle. If, during the batch, the screwdriver remains idle for a time exceeding the 'dt' value, 
an audible alarm will sound and the display will flash 'dt' until the driver is triggered for the next cycle.
(Note: depending on other program settings. the operator may need to press 'S' to continue driving 
screws if 'dt' is flashing in the display.)
The 'tt' Total Batch Time Alarm can be set in 1 minute intervals. If the batch is not completed within the 
'tt' time setting, an alarm will sound and the display will flash 'tt' until the operator runs the driver and 
completes the batch. Only one of the two optional alarms can be selected for use.

Adjust value 
UP / DOWN

Press until 'dt' 
or 'tt' displays. 
Release to 
view value

Adjust value 
UP / DOWN

Toggle value

Toggle value

The controller also has a selectable slow start option. This option can be helpful in engaging screw threads 
properly to avoid cross threading. The slow start is intended for initiating the fastener rundown only – the 
slow start time must be limited so that the tool switches to full speed before the fastener completed its 
rundown.

The 'Sr' value is valid when the controller is set to run 
multiple sequences (DIP SW6 On) and the batch enable 
input (DIP SW2 On, or DIP SW2 & 4 On) is being used 
to confirm the batch start via an external switch. If 'Sr' 
is set to the default value of 'n' (no), the controller will 
require an external enable input at the beginning of the 
first sequence U1 only. 
If 'Sr' is set to 'y' (yes), the controller will require an 
enable input at the beginning of each sequence (eg. U1, 
U2 and U3 will all require an enable if 3 sequences are 
running sequentially).

If 'dt' = 00, the display will prompt for input of a 'tt' value.

Hi =

 use a normally closed contact, momentarily open to enable

Lo = 

use a normally open contact, momentarily close to enable

Содержание 035/E32V




























Отзывы: