Bosch T1 Alternator Скачать руководство пользователя | Manualshive

Страница: 25 / 45

background image

Repair and Testing Instructions for T1 Page 25

Alternator 0120 689 552

Edition 001

All rights rest with Robert Bosch Corp, including patent rights. All rights of use of reproduction and publication rest with R. B. Corp.

UA/ASV

04.12.98

T1ALTFinal.DOC

9.15 Rotor Inspection

1. Using electric tester ETE 014.00 or Multimeter MMD 302, measure the resistance between the two collector

rings of the rotor. The resistance measured should be between 7.5 and 8.3 . (Figure 21)

2. Using insulation tester KDAW 9983 or equivalent, apply 80 VAC to the rotor claw poles and each of the

collector rings. If the insulation tester lights, there is a short to ground within the rotor. (Figure 22)

Note: The insulation tester applies a voltage of 80 VAC to the rotor. Voltages of 80V can be fatal.
When performing this test, observe care is used in handling the rotor and any component or surface
that is exposed to the rotor. Use insulated gloves and do not touch the work surface until all tests are
completed.

3. Mount the rotor in a pair of V-Blocks at the rotor bearing points.

Figure 21 Rotor Resistance Testing

Figure 22 Rotor Insulation Testing

«
...
23
24
25
26
27
...
»

Содержание T1 Alternator














































Отзывы:

Нет отзывов

Похожие инструкции для T1 Alternator

WJHD100 - DIGITAL DISC RECORDE

Бренд: Panasonic Страницы: 7

Бренд: Tate Страницы: 7

Бренд: Tate Страницы: 5

BioHarmonex BH4

Бренд: Calivita Страницы: 38

Бренд: CAIRE Страницы: 91

PowerXL DX-NET-ETHERNET2-2

Бренд: Eaton Страницы: 48

Power Xpert C445

Бренд: Eaton Страницы: 2

Бренд: Ibiza Страницы: 21

Бренд: IBASE Technology Страницы: 67

Бренд: IBC Страницы: 8

Бренд: Ibanez Страницы: 8

Бренд: IAI Страницы: 5

Бренд: Landi Renzo Страницы: 16

Бренд: IBM Страницы: 163

Бренд: Yamaha Страницы: 48

Wallach UltraFreeze

Бренд: Cooper Surgical Страницы: 4

Бренд: Ametek Страницы: 20

Бренд: VibraPEP Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды