Bosch T1 Alternator Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 45

background image

Repair and Testing Instructions for T1 Page 22

Alternator 0120 689 552

Edition 001

All rights rest with Robert Bosch Corp, including patent rights. All rights of use of reproduction and publication rest with R. B. Corp.

UA/ASV

04.12.98

T1ALTFinal.DOC

5. If the roller bearing is stuck in end shield, proceed as follows:

a.

Remove extractor KDLJ 6009 from the bearing.

b.

Destroy the bearing cage with a screwdriver or similar tool.

c.

Remove rollers from bearing.

d.

Insert spring collet KDAW 9995/6 (Bosch Number 0 986 619 233) into bearing outer race.

e.

Screw threaded rod KDAW 9995/14 into extractor KDAW 9995/6.

f.

Slide the receiver cup KDAW 9995/0/5 onto threaded rod.

g.

Screw on handle and rotate until the bearing race comes out of the collector end shield.

9.11 Removal of Sliding Bushing in Collector End Shield

1. Place collector end shield in an arbor press, support mounting/pivot boss on mandrel KDLJ 6016 (Bosch

Number 0 986 618 130). (Figure 17)

2. Place bushing mandrel KDLJ 6015 (Bosch Number 0 986 618 219) on sliding bushing.

3. Press sliding bushing out of collector end shield into mandrel KDLJ 6016.

9.12 Removal of Rotor from Drive End Shield

1. Place drive end shield onto pressing ring KDLJ 6013 (Bosch Number 0 986 618 127).

2. Place pressing ring into an arbor press. (Figure 18)

Figure 17 Sliding Bushing Removal

«
...
20
21
22
23
24
...
»

Содержание T1 Alternator














































Отзывы:

Нет отзывов

Похожие инструкции для T1 Alternator

Бренд: Baker Hughes Страницы: 168

Бренд: Gatekeeper Страницы: 8

Bure Rise & Go DB 56-309

Бренд: Gate Страницы: 8

Бренд: Hach Страницы: 66

Бренд: Hach Страницы: 14

Бренд: Hach Страницы: 144

QuikChem 8500 2 Series

Бренд: Hach Страницы: 80

Бренд: Hach Страницы: 178

Бренд: Hach Страницы: 32

Бренд: hager Страницы: 4

Бренд: TC Electronic Страницы: 4

Бренд: TC Electronic Страницы: 6

Бренд: TC-Helicon Страницы: 12

Бренд: TC Electronic Страницы: 76

Бренд: Ultraflex Страницы: 48

Бренд: Garmin Страницы: 2

Бренд: Parker Страницы: 58

AirForm Night Splint

Бренд: Össur Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды