Bosch SHP65TL5UC Скачать руководство пользователя страница 50

Страница: 50 / 82

702_58300000170749_ara_en_c

Page 50 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

5.4.2

To remove door latch

Tools needed: Flat blade screwdriver and pliers.

Disconnect & pull out dishwasher

– section 5.1.5.1.

2. Remove door latch by carefully prying tank tabs and lifting

the latch up and away from the tabs

(below)

HINT:

When replacing a door latch:

•

Make sure the door latch is aligned, is held securely

and the sensor detects the door latch magnet.

•

Misaligned latches can prevent dishwashers from
starting

. If the dishwasher won’t start, check the door

latch alignment.

5.5

Water valve

Access the water valve from the rear of the dishwasher base by
pulling out the dishwasher.

5.5.1

To remove water valve

Tools needed: Flat blade screwdriver and pliers.

Disconnect & pull out dishwasher

– section 5.1.5.1.

2. To gain slack to pull out water valve, loosen hose clamp

from water inlet hose

and pull water inlet hose from

water inlet

control

(below)

3. Push up latch and carefully pull water valve and mounting

bracket up and away from base

(below left)

Содержание SHP65TL5UC



















































































Результаты поиска

Содержание SHP65TL5UC

Отзывы:

Похожие инструкции для SHP65TL5UC

Бренды по названию

Популярные бренды

Bosch SHP65TL5UC, Инструкции по ремонту

Результаты поиска

Содержание SHP65TL5UC

Отзывы:

Похожие инструкции для SHP65TL5UC

Бренды по названию

Популярные бренды