Bosch SHP65TL5UC Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 82

Bosch SHP65TL5UC Скачать руководство пользователя страница 38

702_58300000170749_ara_en_c

Page 38 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

4. Carefully push the pocket handle

out

of the outer door (i.e.

push from the

inside

of the door).

CAUTION:

Outer door edges (at the handle cutout) are

sharp! Use gloves and remove pocket handle carefully.

5.1.2.4 To remove fascia panel

Fascia panels and outer doors are both removed by removing
inner door screws. For most dishwashers, the top four (6) screws
hold the fascia panel, except for the two (2) small screws holding
the door latch (Hall Effect) sensor.

Tools needed: T-20 Torx screwdriver

.

1. Remove fascia panel by removing six (6) long fascia panel

screws from top of inner door

(below left)

. If needed,

remove outer door first (section 5.2.1.1).

2. Lift fascia panel out from door. Be careful to not damage

wire harnesses. The

slightly

longer six (6) fascia screws

are different than the shorter six (6) outer door screws, so
don’t mix screws when removing both fascia panel and
outer door

(below right)

.

5.1.3

Side access

5.1.3.1 Left side access

The water inlet control (with condensation vent), water inlet hose,
sump hose and drain hose are accessible from the left side.

5.1.3.2 Right side access (power module)

The power module is accessible from the right side.

1

2

3

4

1.  Water inlet control
2.  Drain hose
3.  Sump hose
4.  Water inlet hose

«
...
36
37
38
39
40
...
»

Содержание SHP65TL5UC



















































































Отзывы:

Нет отзывов