Bosch SHP65TL5UC Скачать руководство пользователя страница 48

Страница: 48 / 82

702_58300000170749_ara_en_c

Page 48 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

4. Carefully pry inner door flanges

(1)

away from the tabs

(2)

on the top and bottom of the dispenser

(see below)

5. Carefully push the dispenser in through the inner door (i.e.

toward the dishwasher tank).

CAUTION:

Inner door edges are sharp! Use gloves,

cover inner door edges and remove dispenser carefully.

5.3.2

To install dispensers

1. Where necessary, bend back inner door flanges so they

can snap into dispenser tabs.

2. To aid installation, coat dispenser seal with rinse-aid.

3. Carefully push the dispenser out through the inner door

(i.e. from inside the dishwasher toward the front of the
dishwasher).

4. Snap inner door flanges onto or into dispenser tabs.

5. Reconnect dispenser wire harnesses.

6. Replace or reinstall vapor barrier – section 5.4.3.

7. Replace cable guide.

8. Replace outer door.

CAUTION:

Inner door edges are sharp! Use gloves,

cover inner door edges and install dispenser carefully.

Содержание SHP65TL5UC



















































































Результаты поиска

Содержание SHP65TL5UC

Отзывы:

Bosch SHP65TL5UC, Инструкции по ремонту, Страница: 48 / 82

Результаты поиска

Содержание SHP65TL5UC

Отзывы: