Bosch SHP65TL5UC Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 82

background image

702_58300000170749_ara_en_c

Page 26 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

4.10 Door spring

The door spring mechanism uses a “sliding” pulley and cord to
provide proper tension and enable self-closing. The fixed sliding
pulley is attached by two screws (including one inside the bottom
pulley). The cord slides on the pulley, using the friction between
it and the cord to provide better control.

The spring slides into a slotted pocket in the side of the base and
connects to the cord. Springs are color coded for specific
tensions.

4.11 Terminal box

All dishwashers have terminal boxes with covers, conduit / cord
exits and dishwasher cords. The dishwasher cord plugs into
the power module, accessed through the left rear of the
dishwasher base.

4.11.1

Terminal block

Terminal blocks clearly show line (

L

), neutral (

N

) & ground (

)

connections. Dishwasher cords have spade terminals which
connect to terminals on the terminal block.

NOTE

: An optional power cord is available, which plugs

into the power module and replaces the junction box with
cord provided with the dishwasher (SMZPC002UC –
service #

747210

).

1 2

3

4

1.  Cord holder
2.  Sliding pulley
3.  Cord
4.  Door spring

„Click“

NOTE

: The plug has

notches which keep
it plugged into the
power module.

1. Notch

1

«
...
24
25
26
27
28
...
»

Содержание SHP65TL5UC



















































































Отзывы:

Нет отзывов

Похожие инструкции для SHP65TL5UC

Бренд: Caloric Страницы: 12

Бренд: Unimac Страницы: 2

Бренд: Fagor Страницы: 22

Бренд: Sammic Страницы: 48

Бренд: ZANKER Страницы: 68

Бренд: Hoover Страницы: 17

Conservator 3955874A

Бренд: Crosley Страницы: 8

Бренд: Hotpoint Страницы: 16

Бренд: Galanz Страницы: 10

Бренд: Asko Страницы: 24

Бренд: Kuppersbusch Страницы: 56

Бренд: Frigidaire Страницы: 20

Бренд: GE Страницы: 16

Бренд: GE Страницы: 48

Бренд: GE Страницы: 16

Бренд: GE Страницы: 16

Бренд: GE Страницы: 32

Бренд: GE Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды