English |
7
Bosch Power Tools
1 619 929 L51 | (17.7.12)
– Hold the switched on drill with the attached drill bit sharp-
ener as shown in the figure.
Pay attention that the ventilation slots of the drill are not
obstructed.
– Sharpening the first cutting edge of the drill bit:
Insert the drill bit into the smallest fitting hole of the drill bit
sharpener. Swiftly twist the drill bit approx. 10 times back
and forth between the left and right stop while applying
light pressure (for small diameter drill bits approx.
5 times).
– Sharpening the second cutting edge of the drill bit:
Pull the drill bit out a little, turn it by 180° and guide it back
in to the grinding wheel
6
. Twist the drill bit as described
under sharpening the first cutting edge of the drill bit.
– Repeat the complete procedure as required until both cut-
ting edges are sharp and symmetrical.
Checking and Correcting (see figure D)
The cutting edges
S
of the drill bit must be uniformly long.
– If not, point the shorter cutting edge toward the inner mark
of the matching hole of the drill bit sharpener.
– Guide in the drill bit in this position and twist it approx.
3 times back and forth from stop to stop.
– Check the result and repeat the procedure as required.
Maintenance and Service
Maintenance
Readjusting the Grinding Wheel (see figure E)
The grinding wheel
6
should be readjusted after approx.
100 sharpening applications.
The drill bit sharpener has to be disassembled for this.
– Loosen fastening screws
4a
and then loosen fastening
screw
4b
.
– Remove the spacer
5
.
– Mount the drill bit sharpener in reverse order without the
spacer.
Replacing the Grinding Wheel
Replace the grinding wheel
6
after approx. 200 sharpening
applications.
The drill bit sharpener has to be disassembled for this.
– Loosen fastening screws
4a
and then loosen fastening
screw
4b
.
– Mount the spacer
5
on the new grinding wheel.
– Mount the drill bit sharpener in reverse order.
Spare Parts
In case of loss of the drive element
1
, use a 90 mm long (or
longer) M8 hexagon bolt.
– Shorten the bolt to the matching length (see “Adapting the
Drive Element”, Page 6).
After-sales Service and Customer Assistance
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Our customer service representatives can answer your ques-
tions concerning possible applications and adjustment of
products and accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: [email protected]
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: +61 (01300) 307 044
Fax: +61 (01300) 307 045
Inside New Zealand:
Phone: +64 (0800) 543 353
Fax: +64 (0800) 428 570
Outside AU and NZ:
Phone: +61 (03) 9541 5555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: +27 (011) 6 51 96 00
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: +27 (011) 4 93 93 75
Fax: +27 (011) 4 93 01 26
E-Mail: [email protected]
Article number
Grinding wheels
2 608 600 029
OBJ_BUCH-1723-001.book Page 7 Tuesday, July 17, 2012 3:00 PM
