Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 206

Страница: 206 / 422

6.5.4

XG3, motor temperature monitoring and motor holding brake

Dangerous movements! Danger to persons

from falling or dropping axes!

WARNING

The standard motor holding brake provided or an external motor holding

brake controlled directly by the drive controller are not sufficient on their own

to guarantee personal safety!
Personal safety must be achieved using higher-level, fail-safe measures:
●

Block off danger zones with safety fences or safety guards

●

Additionally secure vertical axes against falling or dropping after

switching off the motor power by, for example,
–

mechanically securing the vertical axes

–

adding external braking/arrester/clamping mechanisms

–

ensuring sufficient equilibration of the vertical axes

Lethal electric shock from live parts with more

than 50 V!

WARNING

The input of the motor temperature evaluation is not galvanically isolated

from the housing. Excess voltage at the input (e.g., by the motor winding

voltage flashing over) can get to the housing. Make sure that the temperature

sensor of the connected motor is double-insulated from the motor winding.

Risk of damage to device from excess

voltage at motor temperature evaluation

input!

NOTICE

Only the allowed control voltage for the device is allowed at the motor

temperature evaluation input. Excess voltage at the input can damage the

device.

Function

Connection point XG3 contains the connections for
●

Monitoring the motor temperature

●

Controlling the motor holding brake

Via an integrated contact element (BR), the power section

switches the voltage of the external 24 V supply to the output for

controlling the motor holding brake.

View

Connection

Signal name

Function

Motor temperature

evaluation input

MotTemp-

+24VBr

Output for controlling the

motor holding brake

0VBr

Tab. 6-42:

Pin assignment

192/407

Connection points

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды