Bosch REXROTH IndraControl VAM 12.1 Скачать руководство пользователя страница 5

Страница: 5 / 96

Page

Enabling Button of the Hand-Held Terminals IndraControl VEH 30.1, 30.2 or VCH 08.1.............. 49
STOP Button of the Hand-Held Terminals IndraControl VEH 30.1, VEH 30.2 or VCH 08.1.......... 50

6.2.8

Pushbuttons on the VAM12.1-PB-NF-NN-TB-VD-NN-1608-NN and VAM42.1-PB-NF-NN-TB-VD-

NN-1608-NN...................................................................................................................................... 50

6.2.9

Pushbuttons Customized Variant "D1".............................................................................................. 51

Interfaces..................................................................................................................... 53

7.1

Connector Panel................................................................................................................................... 53

7.2

Protective Earth Terminal..................................................................................................................... 53

7.3

X10: Current and Voltage Supply ........................................................................................................ 53

7.4

X71: Fieldbus Interface PROFIBUS DP X71........................................................................................ 57

7.4.1

General Information........................................................................................................................... 57

7.4.2

Pin Assignment.................................................................................................................................. 58

7.5

X21, X22, X11: Digital 24 V Inputs and Outputs................................................................................... 58

7.5.1

General Information........................................................................................................................... 58

7.5.2

Pin Assignment (3 × 8-Pin Weidmüller Connector, 3.5 Pin Spacing)................................................ 59

7.5.3

Characteristics of the Digital Inputs................................................................................................... 60

7.5.4

Characteristics of the Digital Outputs................................................................................................ 60

7.6

Wiring of the Pushbuttons and of the EMERGENCY STOP button for Customized Device Variant "D1"

.............................................................................................................................................................. 61

7.6.1

Wiring of the Pushbuttons and of the EMERGENCY STOP Button VAM 12.1, Device Variant "D1"....

7.6.2

Wiring of the Pushbuttons and of the EMERGENCY STOP Button VAM 42.1, Device Variant "D1"....

7.7

X81: Connection for External Hand-Held Terminal............................................................................... 62

7.7.1

General Information........................................................................................................................... 62

7.7.2

Pin Assignment (25-Pin Female Connector Strip, D-SUB................................................................. 63

7.8

X82: Connection for Internal Handwheel.............................................................................................. 64

7.8.1

General Information........................................................................................................................... 64

7.8.2

Pin Assignment (6-Pin Weidmüller Connector, 3.5 Pin Spacing)...................................................... 64

7.9

Connecting a Hand-Held Terminal IndraControl VEH 30.1, VEH 30.2 or VCH 08.1............................ 64

7.9.1

Overview............................................................................................................................................ 64

7.9.2

Pin Assignment of the VAC 30.2 Connection Module ...................................................................... 65

7.9.3

X1: DC 24 V Voltage Supply VAC 30.2............................................................................................. 66

7.9.4

X2.1: STOP Button VAC 30.2 ........................................................................................................... 67

Pin Assignment............................................................................................................................... 67

7.9.5

X2.2: Enabling Button VAC 30.2 ...................................................................................................... 67

Pin Assignment X2.2...................................................................................................................... 67
Wiring the Enabling Button............................................................................................................. 68

7.9.6

X3: Ethernet Interface VAC 30.2 ...................................................................................................... 68

7.9.7

Personality Function.......................................................................................................................... 69

Maintenance and Commissioning................................................................................ 71

8.1

Maintenance......................................................................................................................................... 71

8.2

Torques and Stripping Length.............................................................................................................. 71

8.3

GSD File............................................................................................................................................... 71

DOK-SUPPL*-VAM*XX.1***-PR02-EN-P
Rexroth IndraControl VAM 12.1/42.1 Machine Control Panels

Bosch Rexroth AG

III/93

Table of Contents

Содержание REXROTH IndraControl VAM 12.1

































































































Результаты поиска

Содержание REXROTH IndraControl VAM 12.1

Отзывы:

Похожие инструкции для REXROTH IndraControl VAM 12.1

Бренды по названию

Популярные бренды

Bosch REXROTH IndraControl VAM 12.1, Руководство по планированию проекта

Результаты поиска

Содержание REXROTH IndraControl VAM 12.1

Отзывы:

Похожие инструкции для REXROTH IndraControl VAM 12.1

Бренды по названию

Популярные бренды